Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi all,
I am testing DFU example in Mesh SDK . I follow this tutorial : http://infocenter.nordicsemi.com/index.jsp . But when I execute to step 4 :
I get this error...
Hello,
I am new to Nordic products so please apologize me if I am asking a trivial question, but a bit lost on it. I would like to use Thingy 52 board for my project ( I...
Hello,
I am having a trouble with my code. There is an RTC sensor Which has the address 0x32. When the sensor is connected to the TWI lines, there is no problem and it...
Hi There,
I've been developing a product using the NRF52DK. I had some custom PCB's made after I had my circuit designed, and I programmed them with the NRF52DK. Now my...
This one is weird. On a new board with a Rev C '840, when trying to reset the processor using 'nrfjprog --program nuttx.hex --sectorerase --erase', a Decawave DW1000 connected...
I want to add ANCS client to my code. Like in the ble_app_ancs_c example, I start a timer after BLE_GAP_EVT_CONNECTED. The timer handler calls pm_conn_secure() if the connection...
Hello
SDK12.3, nRF51822
I'm trying to interface the ssd1306 the program freezes in function app_twi_perform internal_transaction_cb is not called internal_transaction_in_progress...
With our nRF53832 device we are not using NFC.
For the lowest power usage should I keep them as disabled NFC pins or change them to GPIO pins and drive them to the same...
Hi!
I have a question regarding nRF51822 supply in internal LDO setup. Is decoupling capacitor on pin DEC2 necessary in this supply setup? Looking at schematic in nRF51...
Hi! As far as understood, there are only 2 clock cycles before the Watchdog timer reset occurs. Is there a way to change/set this to a different value? I need to write in...
Hello!
When using the NRF_LOG module along with a JLink, when I connect the probe to the nRF the RTTClient prints out the first lines that were written when the probe was...
i comple the ble_app_proximity in SDK15, Config APP_ADV_DURATION for 10s,after timeout, no BLE_ADV_EVT_IDLE occur in on_adv_evt.
how put the system into sleep mode?
Hi,
how can i merge ble_app_beacon with mesh sdk beaconing example?? I want to advertise sensor data into beacon advertisement packet. all beacons should be formed a mesh...
Hi All,
I am trying to use TWI on NRF52832 using SDK 12.3 + SD132 but without any success.
For some reason, there is no signal coming out on the configured SDA + SCL pins...
