Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hello
I am playing with the mesh dfu and the distributor application on nRF52840 DK board
I load the image I want to distribute using mcumgr application on a Raspberry...
Hello
According to Enhanced ShockBurst (ESB) documentation , to stop the ESB module you need to call esb_disable(), but it also says that you need to check if the module...
Hello,
We are considering to develop an appliance based on the nRF5340 AUDIO DK.
The nRF5340 AUDIO DK contains the VM3011-U1microphone that is absolute on the market....
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
Hello Nordic Team,
I’m trying to use the nRF54L DK to program an external MCU via SWD , but I’m encountering an error during connection. I’ve already followed this guide...
I'm trying to build the light-switch-app from Matter but I get following errors
I have already tried to reinstall the sdk (I use v2.8.0) and build it just like that without...
After modifying the factory data with the script generate_nrfconnect_chip_factory_data.py, the discriminator and passcode work, but how do I change the value of the Manual...
I am trying to interface an SD card with the nRF9160-DK using an SD card adapter module. My goal is to write the string "hello" to a .txt file on the SD card. I believe I...
Is a TVS diode clamping voltage of 6.5 V acceptable for supplementing the built-in ESD protection of the NRF52840 GPIO pins?
It has been previously established in the forum...
Hello everyone!
I am rather new to firmware development with Nordic products and am experiencing some trouble with the Thingy91 LTE BLE Gateway sample.
What is the problem...
Hello,
I want to set my TTL value in a node (nrf52840 dongle) that i use as a relay node.
In prj.conf file I set the node in this way:
CONFIG_BT_MESH_RELAY=y
CONFIG_BT_MESH_RELAY_RETRANSMIT_COUNT...
Hi
I've recently tried to move from SDK version 2.6.3 to 2.9.1. However i've run into issues with this transistion.
I made a new custom board, by following the guide...
Hi , i am trying to use ble channel sounding feature through hci uart with an external host. I am sending CS commands but getting the following error for one of the commands...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
I want to realize the connection and communication between the broadcaster and the upper computer software nRF Connect...
