Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello, I´m trying to compile the BLE Heart Rate service projects using SEGGER Embedded Studio. After importing the project from nrf52 SDK, I tried building the project but...
Hello,
I want to implement home automation project using 3 nRF52840 dongles. i.e I want to connect all the 3 dongles with each other and the signal sent from one device...
Hello, I am trying to design a product based on BLE MESH. I would need gateway to be able to accumulate data from network and send it outside. I need that gateway to connect...
Hi,
I have gone through the "ble_app_hids_mouse" example program. So far the program seems to work great, but how do we take control of the buttons since the function used...
Hello,
We have plan to use nRF52832-CIAA with external antenna connector (MHF4). I noticed that in 4-layer reference design layout there is quite big square keepouts on...
Hi,
I am using sdk 14.2.0.
i am using freeRTOS,created 3 threads.
all are running fine,but just for while(2 - 3 minutes).
after that, all the threads stoped.
may...
Hi,
I am doing OOB commissioning with OpenThread. According to section 10.12 of Thread 1.1.1 specification, Active / Pending Operational Datasets need to be persisted to...
Hello,
I'm trying to connect external RTC, which has a 32kHz clock on it's pin to nRF52832. So far I've had issues with connecting this clock to P0.00 pin and having P0...
Hi all:
when i add uart code in ble_multilink ,and it gived me errors like this:
"<error> app: Fatal error <warning> app: System reset <error> app: Fatal error <warning...
If I put too many characters into a serial using IRQ mode, it stops reading input.
I haven't tried polling or DMA yet.
Using
nRF5_SDK_15.0.0_a53641a
gcc-arm-none...
Hi ,
can u please provide more details about error code 4, returned by ble_ancs_c_init function.
what is this error, and how to resolve it???
thanks,
amarjeet
Hi there,
we are developing an application based on simple IEEE 802.15.4 packets, for which we use the radio peripheral. Every example found in the SDK starts with switching...
Hi
I would like to perform a connection over 2MPHY instead of 1MPHY; is there an example to show this? This should be doable according to the softdevice v6.1.0 changelog...
Dear Nordic
I am doing a project that has a multilink one central and ten peripherals.
So I started with ble multilink multi role in here . I added ble_nus_c and uart...
