Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
My app (SDK12.3.0 + S130 v2.0.1) is being prevented from advertising because flash_access_in_progress() is true (m_queue.count != 0) on ble_advertising_start (ble_advertising...
Hi! I'm trying to add the nRF drv_timer library to the ble_app_template example project (BLE Peripheral).
I have added the nrf_drv_timer.c file to the project, and the directory...
I need to switch between 3 central devices (device slots, rather) with a peer manager and SDK 12.3.0 (nrf51822-based keyboard, see sdk12_3 branch for a peer manager https...
Hi,
I have a problem, like this fellow engineer here , but the solution is not applying for me.
Our firmware support different modes of operations. Mode changes are...
Hi,
I was testing out the nrf52840, and i wanted to initialize the BNO_080 sensor with the nrf52840 DK. Now, i realized that if i want to read from registers to get the...
Hi, I'm using nRF52840-DK , SDK 15.0, buttonless DFU sample + secure bootloader I see that resuming DFU works only after disconnect, but no longer on sw reset or power down...
Hello
I have seen in the various examples that most of the time the output are digital (0 or 1) . i program a PWM signal to make any DC output on the pin 18
but unfortunately...
I am developing a windows deskop application for BLE devices.
which laungage is the prefered for this type of Desktop application having predefined libraries..
Nordic...
We have an application running on a custom board with the following configuration:
nrf52832
SDK v12.3
Softdevice S132 v3.1.0 and S332 v2.0.0 (different variants of PCB...
Hi, I am using nRF51822 now,SDK11.0, how to let the peripheral open the peer's notification, My original design uses DA14580, Android APP can receive messages when the peer...
hello .
i am trying to open driver in the advertising.py example pc-ble-driver-py-master
driver.open() and this line throw exception
if err_code != expected: raise NordicSemiException...
It seems nordic devices can not be programmed without certain segger software.
In order to set up my toolchain, I had to install SEGGER Embedded Studio IDE (although i dont...
I have seen nordic contains QDID 111537 for mesh profile subsystems. Is this profile subsystem includes the Mesh Model or nordic have a plan to get Mesh Model QDID seperately...
Hi.
I'd like to disable retransmission in my Thread application built with SDK for Thread and Zigbee 1.0. I followed the instructions from Infocenter "Building the latest...
