I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Does the NRF51 DK come with a SWD interface connector-cable to plug into a PCB's SWD port when flashing/programming code into a WLCSP chip soldered onto the PCB? If not, are...
I'm trying to setup a simple host node to broadcast a attention message with no definitive destination node. I need any of the child nodes (primarily asleep) to see and process...
Hello everyone,
I tried to use the example project " ble_ant_app_hrm" SDKv14.2 but it doesn't work. The bluetooth connection work correctly, I connect my smartphone with...
Hello Nordic
I am developing our device. It uses SDK 14.2.0 and s332 SoftDevice.
This device communicate our app by using ble as peripherals.
I thought that our project...
Hi,
do the AES CCM module, AES ECB module, and the Cryptocell 310 (in nRF52840) employ measures against side channel attacks? I am mainly concerned with timing analysis...
Hi all,
I'm working with nRF52840 PDK and I'm using the last SDK and SoftDevice version: SDK v15.2.0 and SoftDevice v6.1.
I'm using the scanning module introduced in this...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
I am experimenting with light_switch server example from mesh SDK 2.1.1 . I want to add UART functionality to this example.
I referred to the ble_app_uart example from sdk15...
after cmake -G Ninja ..
-- SDK_ROOT=C:/BLE/SDK/nrf5_SDK_for_Mesh_v2.2.0_src/../nRF5_SDK_15.0.0_a53641a --- set with command line ARG -- PC-Lint executable not found. Linting...
Hi ~ SDK: nrf5_SDK_for_Mesh_v2_0_1 's ligth switch proxy client & proxy server IDEs : SEGGER Embedded Studio for ARM Release 3.40 Build 2018052200.36079 Windows x64 SoftDevices...
I'm looking for the nRF5x SDK v14.2.0-SR3 tha is written on the Smart Remote 3 for nRF52 user's manual. I could not find it on the DevZone, https://developer.nordicsemi.com...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
