Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Sending array unit8 type data using BLE failed, and attempting to take 2 bytes of data from the array and send it also failed. Does anyone know what this log error means?...
Hello,
Since a few days ago, when I start VS Code, I get the following warning:
But when I check the settings in VS Code, v1.x.x is not there.
What could be the...
I have a Raytac MDBT50Q-CX and cannot seem to flash it correctly. The flash succeeds, but the device is no longer recognized by Windows or (raspberry pi) Linux.
My goal...
I am currently working with the nrf54l15, I have both the DK and a custom board I designed. I am running into issues with the uart00 peripheral when using custom GPIO pins...
Hi,
I am using nRF52840 DK and I am following Nordic Academy nRF Connect SDK Fundamentals. I installed SDK 2.9.1 and toolchain 2.9.1
I copied the sample blinky and encountering...
Hi everyone,
I'm using the nRF54L15-DK and trying to implement a simple low-power cycle where the board:
Measures sensor values
Sends them via CoAP over OpenThread...
I am migrating from a child_image type project to the newer sysbuild system used in ncs v2.9.0.
My application is based on the ncs nrf5340_audio application, but my application...
Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hi everyone,
Environment setup: - I am using Zephyr OS 2.5.0 running on nRF52840 board. - MIRA mesh integrated in the application.
Problem description: - Firmware A has...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
Dear All,
We have a custom design with a nRF9160 powered by Lithium primary batteries.
When batteries end of life is coming or sometimes when harsh environmental operating...
Hi,
USB CDC EPOUT stops working as the USB incoming traffic data rate increases. The symptoms of this issue align with the Errata 199. The workaround for Errata 199 is...
I'm currently working on a custom board based on the nRF52840 , using SoftDevice S140 v7.0.1 and nRF5 SDK v16.0.1 . I’ve integrated the BLE Buttonless DFU example ( examples...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
