Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
when performing db discovering using a peripheral nrf52832 (running sample dfu project) from sdk 13 from a nrf32832 central on sdk 14 I notice that the db discovery event...
Hi Sir
I would want to download code to Ublox NINA-B301 by command line, but it looks not working, please help.
nrfjprog.exe -i 483064601
nrfjprog.exe --family NRF52...
Hi,
I'm trying to perform a DFU firmware update via command line using nrfutil dfu ble.
The same update using nRF connect works fine. The dongle is flashed with connectivity_1...
I would like to have a ZigBee stack running on the 52840 and use door/window (contact) sensors as well as motion (PIR) that are available on the market today to connect to...
Dear Sirs!
I use compiler IAR 7.80 with Nordic SDK 12.2
Softdevice
s132_nrf52_3.0.0_softdevice.hex
I have very strange issue in debugger.
Break point works, but...
Hi folks,
I try change blinky code for nRF52810 SoC. I must create own timer. I dont know app_timer example help for me?! I want to do when power on leds on 2 seconds...
Hi All,
I am developing an application in which i am interfacing the nRF52832 with an ADC via SPI.
I am doing channel multiplexing (2 channels) such that when i get data...
I'm aware of the limitations on using "printf" in a non-debug environment, but apparently there must be something similar with sprintf. I'm using it to load a value into a...
Hello,
There's a problem compiling the standard ble_app_uart_pca10040_s132 in Segger Embedded Studio for ARM V3.40. The UART example is straight out of nRF5_SDK_14.2.0_17b948a...
Based on the demonstration video of Thingy , I can have a view on Thingy is changing its color when it is given different command using the apps.
1. As if I want to send...
Hello, I want to include Mesh Serial Example into the Mesh Light Switch example.
The aim is to allow the serial device to listen to the mesh messages.
What is the best...
Hi Everyone
I am using BLE for NORDIC UART SERVICES. I want to update my code via BLE instead of a USB or J-LINK.
How can i upload my code from the Android device to nrf52840...
Hi,
I am working on nRF52840 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
I am trying to bring up UART on my custom board.
So as a first...
I followed test steps mentioned in dfu_quick_start.md file to perform DFU over mesh.
1. Below is the error i am getting while creating DFU package, Please help on this....
