Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi,
Is nRF51822 / S110 capable of simultaneously being in peripheral (connected slave) and broadcaster (broadcasting non-connectable ads) mode? The datasheet says both...
Hi,
I need to write data in to flash memory of the nRF51822 device.
I have tried to write data. When i checked memory address where i wrote data i could find that the...
In the nRF8001, after executing the command "ReadDynamicData"... I receive basically a bitstream with many bytes. The idea is to store it in order to be able to, later on...
I'm trying to write a flash buffer but am hitting a vexing error. To initialise the flash buffer (or rather a test initialisation which will hopefully become the flash buffer...
Hi
I would like to interface nRF8001 with a BeagleBone Black (BBB) an ARM cortex-A8 [1].
BBB has a SPI inteface and can support interrupt line input, and its running Linux...
I have an nRF51822 that I would like to be able to issue a soft-reset command under certain circumstances. I'm not using a softdevice in this version of code, so the other...
Hi,
I'm using pstorage, but found some problem. sd_flash_page_erase will not trigger system event after the operation is complete.
In my code, I registered the system...
Are you supposed to be able to nest critical regions using CRITICAL_REGION_ENTER and CRITICAL_REGION_EXIT? Here I mean you have a function which uses a critical region to...
I'm trying to run bootloader from nRF SDKv6 with SDv7 in gcc.
On our custom board, it runs, but does not advertise (sd_ble_gap_adv_start gets called and does not return...
Hi,
I have developed the firmware using nRF51822 Development Kit. I now want to get to put the firmware on nRF51822 chip used in breadboard. I got a smt adapter with nRF51822...
Hi!
When trying to update app using example bootloader for s110, v.7 from nRF Toolbox I get "Device is not supported. Check if it is in the DFU state".
Bootloader is...
Good morning,
In the application I'm developping with nRF51822 anb S110 SoftDevice, the final peripheral product will be installed in a physical non-accessible place. So...
Hello,
I'm working with the example ble_app_multilink_central of S120. In this example, the scan is done correctly in the three channels of advertising?
Thanks!
