Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Hello, I’m currently working on a PDM microphone project using the nRF52840 and the Zephyr RTOS. I’ve been testing the official dmic example from Zephyr (located at ncs/v2...
I am currently developing firmware on Qorvo's DWM3001C module , which integrates the Nordic nRF52833 . I am using nRF5 SDK 17.1.0 and the SoftDevice S140 .
My base project...
Sending array unit8 type data using BLE failed, and attempting to take 2 bytes of data from the array and send it also failed. Does anyone know what this log error means?...
Hello,
Since a few days ago, when I start VS Code, I get the following warning:
But when I check the settings in VS Code, v1.x.x is not there.
What could be the...
I have a Raytac MDBT50Q-CX and cannot seem to flash it correctly. The flash succeeds, but the device is no longer recognized by Windows or (raspberry pi) Linux.
My goal...
I am currently working with the nrf54l15, I have both the DK and a custom board I designed. I am running into issues with the uart00 peripheral when using custom GPIO pins...
Hi,
I am using nRF52840 DK and I am following Nordic Academy nRF Connect SDK Fundamentals. I installed SDK 2.9.1 and toolchain 2.9.1
I copied the sample blinky and encountering...
Hi everyone,
I'm using the nRF54L15-DK and trying to implement a simple low-power cycle where the board:
Measures sensor values
Sends them via CoAP over OpenThread...
I am migrating from a child_image type project to the newer sysbuild system used in ncs v2.9.0.
My application is based on the ncs nrf5340_audio application, but my application...
Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hi everyone,
Environment setup: - I am using Zephyr OS 2.5.0 running on nRF52840 board. - MIRA mesh integrated in the application.
Problem description: - Firmware A has...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
Dear All,
We have a custom design with a nRF9160 powered by Lithium primary batteries.
When batteries end of life is coming or sometimes when harsh environmental operating...
Hi,
USB CDC EPOUT stops working as the USB incoming traffic data rate increases. The symptoms of this issue align with the Errata 199. The workaround for Errata 199 is...
I'm currently working on a custom board based on the nRF52840 , using SoftDevice S140 v7.0.1 and nRF5 SDK v16.0.1 . I’ve integrated the BLE Buttonless DFU example ( examples...
