I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hi,everyone.
I had learn for below Links and compiling is no error.
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104063#104063...
Hi,
I'm having problems to run the Loopback example in the Bluetooth Mesh SDK:
infocenter.nordicsemi.com/index.jsp
I'm receiving a timeout.
My setup is as follows...
This is a duplicate of https://devzone.nordicsemi.com/f/nordic-q-a/35127/spi-master-0-uses-300ua-upon-first-transfer but I wanted to be safe because I pre-maturely verified...
Hi,
I have been working on MPU9250 examples given in here .Though the program runs fine in KeilUvision 5, the output in tera term shows only 0,0,0 for Accelerometer values...
Normally one writes 0 to an event register to reset it.
I am writing a uart driver and when I open my interface I want to prime my transmit pump by setting EVENT_ENDTX to...
Hi all,
What are the default preflashed contents in the out of box nrf52840 flash?
I assume that bootloader is not present. If my assumption is correct how preflashed...
I'm looking at the SDK15 I2S example project using DMA. My dev set up is 52840/Keil.
The project is under: \nRF5_SDK_15.0.0_a53641a\examples\peripheral\i2s
In the callback...
I am new to BLE development, if that helps preface this question.
My goal is to get a BL652 module by Laird working with the BLE UART example from the Nordic SDK. I am using...
We are working on porting an MESH example from Segger to IAR.
We started with the BLE Peripheral Template, and pulled all the code for the light_switch_provisioner into...
Hi, I noticed that Silicon Labs announced their Mobile Mesh application for Android and showed a demo video .
I searched Nordic's GitHub page. However, I couldn't find...
While trying to make a custom server model, based on the on-off model in the documentation, the code breaks when receiving an incoming message. The problem is in the file...
Hi ,
We have designed an Nrf52832 customized board having 32mhz crystal but not having any low frequency clock. The board is working fine with the blinky and other codes...
Hi,
I want control my gpio P0.06 to enable mcp16251, which is a regulator provide power to the nrf52832,
when i trying to control the mcp16251, i found that the gpio can...
Hi,
I'm having some issues getting the ble_app_hids_keyboard example working on Windows 7! While I can pair and connect from Windows 7 the Bluetooth HID driver fails to...
