Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
I noticed that nrf_dfu_flash.c aswell as fds.c both declare m_fs, which collides on compilation.
What is the preferred way to use both modules at the same time, without...
Hi,
For my Master Thesis, I’m working on localization using nRF54L15 boards with BLE Channel Sounding. I’ve been using the official samples available online, specifically...
Hello,
I am currently experimenting with bonding and I stumbled over the config CONFIG_BT_BONDING_REQUIRED.
Currently the BLE characteristics of my peripheral do not require...
Hi,
I have read the documents regarding the powering up the board form external supply and switch position
i need simple answer how power the board completely means...
Hello Nordic team,
I am trying to use external flash on nRF52840dk using Qspi.
Above is my overlay file.
Above is my pm_static file.
I am using custom board where...
I am trying to send a variety of AT commands to my module and it looks like I am missing something or the documentation is not up to date for some of these:
If I try to...
Good morning,
After updating the VSCode extension "nRF Connect SDK" to version v2024.12.55 , I encountered an issue where the "Build" and "Action" menus do not update after...
The datasheet, page 78, says "Supervisor HW to manage power on reset, brownout, and power fail".
We are powering from a solar cell, so the power supply voltage ramp will...
HI i am using nordic nrf52840 dk(pca10056) . i am using ble_app_uart example code for my development. i have connected usb in j2 but when i keep my power switch in usb adv...
Hi! I want to write some software utilizing OpenThread and CoAP. I've seen samples of coap server and coap client in NCS. However, I want to ask whether it's possible or not...
Hi,
I am currently investigating the possibility of using Nordic nRF52840 as the PAwR advertiser and the other device (from a different vendor) as the PAwR scanner. I don...
nRF 52832 + NCS 2.6.1
We are successfully setting the advertising Tx power in discrete steps {-40, -20, -16, -12, -8, -4, 0, +3, +4}dBm using
However, I am being asked...
hi support team,
customer had one problem about 9151 with esim: the iccid can't be readout, it should be 19 bytes string, but we only get 6
may i ask what could be the...
Hi
As described in this white paper: https://infocenter.nordicsemi.com/pdf/nwp_036.pdf during the reference period of CTE signals, 8 samples are taken. These samples contain...
