Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Continuing to port MESH into an IAR project. We would like to make logging work with IAR. Right now, we get a warning that the "format" attribute isn't supported.
Is there...
The valid master out time for <= 8 MHz is shown as tSPIM,VMO 59 ns. The valid master out time for > 8 MHz is shown as tSPIM,VMO,HS 8 ns. The latter tSPIM,VMO,HS could only...
In simple on/off example, the client can turn on several server nodes in the same group in the same time,
but in serial example mix simple on/off server, the info center...
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved. * * The information contained herein is property of Nordic Semiconductor ASA. * Terms and conditions of usage...
Hi there,
I aam using SDK 14 and using all sectors of FStorage. I am using all the sectors of FStorage to read and write data.
After about 24 hours, I see data corruption...
Hello,
So I'm loooking for a way to transfer relatively small quantity of data live as reliable as possible and as quick as possible between two nrf5 units and then between...
Hi,
I am using Nrf51422 DK, my need is to send file (which is placed in my computer)to the another nrf board. Tried with file operations (fopen,fgetc,etc.) in keil4. It...
While flashing program to nrf51822 device through terminal getting these error msg
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists,...
Hello, I currently using the proxy light switch exemple of the mesh SDK 2.0.1 in this configuration :
I search to have the less current consumption in the mesh client ....
Hi all,
Please find my following current measurement resuls in the pwr_mgmt example using a nRF52 preview DK and SDK 13
My setup is as follow:
SB40 is cut
SW6 is...
int main(void) { initialize(); execution_start(start);
for (;;) { (void)sd_app_evt_wait(); } }
can you explain me the execution of code flow in the main with these APIs...
Hi to all,
I am new i ble tech, i read some where that notification charactristic dose not need acknowledgement but indication need, now i want know that this acknowledgement...
Dear all developers：
I want to use whitelist on central mode，and using SDK12.3.0. I have see some call be used like this:
pm_whitelist_set（whitelist_load()）
p m_device_identities_list_set...
Hi,
We are working with SDK 15 with the HRS freeRTOS example. we did some modification to the advertising modes so that we advertise on fast mode for 1 minute and after...
