I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I get to the point of having the EP0SETUP event being generated, I check BMREQUEST and WVALUEH and see that it's a request for the device descriptor,this is on windows and...
Hi, I am using:
SDK v15 with nRF52840 chip running in soft device s140. I am Using Segger Embedded studio.
I want to update a application( Say Blinky) thorugh DFU. I perform...
Hi, I'm using Atomic_FIFO library and for my application I need to know the number of elements currently in the fifo, the library itself doesn't provide any functionality...
Hi,
The program will crash when spi transfer on NRF52810. The crash occurs in spim_xfer function, immediately after spim_int_enable function calling,
but if i remove the...
Hi,
nrf5_SDK_for_Mesh_v2.0.0_src
When complete provision a provisionee , provisioner will assign provisionee a mesh key and device key.
Now i want to know how to calculate...
I can get a clean build and working product with some workarounds, but a couple issues remain from migrating sdk 13.1 to sdk 15.0 (SES nrf52832 s132).
1) After nrf_drv to...
Hi,everyone.
I had learn for below Links and compiling is no error.
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104063#104063...
Hi,
I'm having problems to run the Loopback example in the Bluetooth Mesh SDK:
infocenter.nordicsemi.com/index.jsp
I'm receiving a timeout.
My setup is as follows...
This is a duplicate of https://devzone.nordicsemi.com/f/nordic-q-a/35127/spi-master-0-uses-300ua-upon-first-transfer but I wanted to be safe because I pre-maturely verified...
Hi,
I have been working on MPU9250 examples given in here .Though the program runs fine in KeilUvision 5, the output in tera term shows only 0,0,0 for Accelerometer values...
Normally one writes 0 to an event register to reset it.
I am writing a uart driver and when I open my interface I want to prime my transmit pump by setting EVENT_ENDTX to...
Hi all,
What are the default preflashed contents in the out of box nrf52840 flash?
I assume that bootloader is not present. If my assumption is correct how preflashed...
I'm looking at the SDK15 I2S example project using DMA. My dev set up is 52840/Keil.
The project is under: \nRF5_SDK_15.0.0_a53641a\examples\peripheral\i2s
In the callback...
I am new to BLE development, if that helps preface this question.
My goal is to get a BL652 module by Laird working with the BLE UART example from the Nordic SDK. I am using...
