As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello:
According to the website, please nrf52832 circuit design, without adding other peripherals, just as a radio Beacon, button battery voltage at 2.3 V nrf52832 cannot...
Hello, I am using SDK 15 & Softdevice 6, I am using NRF52840.
I have merged the USB CDC into a multi-link example. I confirmed that it worked, and the project was successful...
Hi
Is the DCDC enabled or disabled by default when using the DTM example in SDK v15.0.0? We can't find any reference to it so we assume it is disabled, but just wanted...
Hi guys,
On my application, I ported the code from TWI_scanner example (SDK14) and it is connected to a temperature sensor the which is read every 45 seconds, It is working...
As far as I can tell, Shockburst isn't officially supported on the nRF52840 in SDK 15. However, I have seen some success from others with this configuration, but after making...
Hi,
I have been working with the NRF52832, and trying to capture raw ADC data with the help of TWI bus. I have imported the necessary libraries (i'll attach the code below...
I have used aes_all_cli example to test computation time for AEAD EAX/GCM/CCM. I have shortened the plain text to 16 bytes, added pin toggling on encryption function enter...
I don’t have a lot of information as I’ve been totally unsuccessful in debugging this.
In short, we have a SPI peripheral that was working under SDK 14.2. Under 15.0 we...
Hi,
I am trying the connect MIO Fuse heart rate band. It follows the standard specified by Bluetooth SIG i.e Heart rate profile UUID is 180D and the heart rate measurement...
I'm currently woking on doing my own DFU system, the system should work this way : the central gets a new version of the app via the internet network and it should update...
How to establish communication with a peripheral through I2C ?what are the functions needed to define address and write and read from the slave address
Hi,
I followed the instructions for importing the Thing:52 firmware into SES and managed to get the firmware compiled and loading, and the code reaches the main function...
Hi,
I'm following DFU quick start guide and I'm using mesh SDK v2.0.1, I have a problem in step 4 wheere I need to generate a hex version of device page, I did this :
...
Hello,
Are there any conditions where the sd_ble_gap_disconnect() will not immediately terminate the link?
My Setup: Nrf52, SDK 13.0.0, own board, based from HRM code...
