Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hello,
currently i am configuring the networking stack on my project.
The goal is to use Matter's built-in Thread connection, to establish a Secure CoAP connection. I...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
I was hoping someone could clarify what support the nRF52840 has for USB power source detection. Our design uses a 150mAh LiPo battery, with a dedicated PMIC. We have the...
I have a hardware with NRF52832 module and successfully used the example twi-scanner to locate my I2C peripheral. I copied these parts over:
My own code produces this...
I am extending the Glucose sensor app in nRF Toolbox (Develop thread). I had logic error which I have corrected, but while debugging I encountered a strange effect that could...
Hi, I have been developing on the nRF52832. I am now in the process of moving to the nRF52810.
I am using the SDK v15.
I have commented out the DEVELOP_IN_NRF52832 define...
The last warning log i had was
E 14:06:57.204 Error 129 (0x81): GATT INTERNAL ERROR D 14:06:57.229 [Server callback] Connection state changed with status: 0 and new state...
Hi Sir
How to config channel and AINx to specific gpio for SAADC ?
For example, if I want read adc voltage from NRF_GPIO_PIN_MAP(0,5), how to set the channel and AIN ...
Hi ,
SDK : nRF5_SDK_15.0.0_a53641a
Chip : nFR52810 【1】Is nRF52810 only use pca10040e （nRF52832 = pca10040 , nRF52840 = pca10056） ? And can't use wrong （nRF52810 use pca10040...
Hello, Nordic
I have to immigrate from SDK14.2 to SDK15. I know that many things have changed in the process.
I'm referring to the Immigration guide but, There is UART...
I am using a PPI to implement a READY line for my SPI slave.
PPI's EEP is set to my SPI slave's EVENT_END
PPI's TEP is set to my GPIOTE's TASK_SET to deassert my READY_n...
Hello,
My previous question is this.
I try to implement sample application with Radio Driver 1.1.0 to SDK15.0.0 ble peripheral uart example.
Symptom
For few micro...
Hi:
I am fairly new to Nordic so please excuse my ignorance. I recently took over a project which used sdk 11 and I am in the process of updating it to 15 and want to see...
Hello,
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery. We need to measure current profile for the beacon and calculate corresponding...
My environment is:
SDK14.1 + SD132 V5.0 + NRF52832
2 sensors(MPU9250 + LPS22HB) 1 battery gas meter (LTC2942) are mounted on TWI ( +1mA)
SPI to spi flash. (+1mA) and...
Hi，
I use SDK is nRF5_SDK_15.0.0_a53641a
【1】In examples proprietary_rf , Here is only the example of pca10040 , So I have to download a lower version of the SDK ?
（...
Hello, I am trying to setup and use the nRF sniffer (ble-sniffer_win_1.0.1) on my NRF51DK (PCA10028) board. I followed the instructions and using nRF studio, I erased all...
