I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
we are developing against the nRF52840 chip. We are interpreting the documentation as indicating that each pin can do all of GPIO, PWM, I2C and SPI. Are we reading this...
Hello,
I'm using SDK 15 and I just started to run the "ble_app_uart" example code. I'm hoping someone can help me find where the data sent from the nRF UART mobile app is...
I am using few keys that are 20 byte arrays, these are unique for each chip. Right now they are hardcoded. I don't want to recompile for each device. I want to write to these...
Hello,
What is the best way to do migration between SDK 11 to SDK 15.
There are guides for each step. Is the best way to do SDK11-SDK12 then SDK12-SDK13... ?
Thank...
Hi,
I just switched over from the nrf52840PDK to the nrf52840DK and I'm running into an issue where the DK board is not firing the NRF_USBD->EVENTCAUSE = Ready event....
Hi,
I'd like to inquire about the recommended configuration for RF conducted emissions testing for the BTLE radio on the nRF52832. As in the reference circuit provided...
I am trying to send more than 255 Bytes of data over I2C so I break it up into 255 byte transfers within a transaction.
I notice a stop/start condition is sent between I2C...
Hi,
I am trying to have two instances of SPI with the same data and clock pins but to two different devices and thus two different select pins.
I have set all the SPI_Enable...
Hi,
The nRF Connect iOS and Android apps provides detailed instructions and functionality for enabling the device boot loader via the iOS/Android] mobile apps. When running...
Hi,
I have a application where the TWI is always reading a sensor in the main task.
When the DFU requiere to reset, frequently the TWI is busy and the current frame is...
I am using nRF5_SDK_15.0.0_a53641a with a nRF52 Development kit. The board is Rev 1.2.4 (the sticker on the bag says nRF6827 and the sticker on the chip says PCA10040). I...
I am struggling to configure all of the options I desire to on the the "ATT-MTU Throughput Example". This is the version provided in the v15.0 of the SDK, with the hex file...
Hi,
I have two nrf52dk devices.
I Want to test the BLE examples which can exchange Bytes of information between each other and display over the UART.
Which examples...
Hi.
My target board has a power switch that is managed by GPIO.
First-time, a user clicks the button, the GPIO is turned on and the system wakes up.
In reset case(Firmware...
