Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi.Is there any inbuilt ic present in nrf52840 DK board to monitor battery management ??if so, how to use that for measuring battery life?can anyone help me out plz!!
Thanks...
Good afternoon, I have a new small, but I think important, question. I did not find a concrete answer on this forum. The question concerns the correct switching of buffers...
I had try to use nRF connect to connect between nRF52840 Dongle and the bluetooth of application.
(I'm not sure the model of bluetooth of application.)
It's connected...
How many crystals/oscillators do I needfor a NRF51822 WLSCP chip?
I looked at datasheet and I'm assuming I will need a 16 Mhz crystal, a 32Mhz crystal, a 16 Mhz oscillator...
I am using IAR workbench and working with the nrf52 DK, using the S132 v.3.0 softdevice. I used the blinky example code to connect the nrf52 with my android phone over BLE...
Hello,
I got TCP Server example working on nRF52DK with Raspberry Pi.
I set everything up and can ping global addresses of DK on all interfaces (wlan0, eth0 and bt0) from...
Hello,
I am using NRF52832, SDK v15.1.0.
For advertising on single channel, I added " p_advertising->adv_params.channel_mask[4] = 03; " in ble_advertising_start() ,...
SEGGER Embedded Studio 3.12
nRF52 SDK 15.0.0
In order to generate peripheral driver library files，how to create library in project(have .c&.h file in this project).Only...
Hi,
SDK documentation says "You cannot write to UICR.BOOTLOADERADDR when using the default J-Link target driver in IAR". Some threads suggested it is only nRF51 issue, but...
Hi!!
Now I am using sdk 14.0.0 / example / peripheral / spi / pca 10040 / blank / arm5_no_packs /
I am sending commands to ads 1192 with nRF 52832 DK as master and after...
I had an issue on using HID to control the media in Android. It worked fine at the first connection, I could play , pause and change the song on phone. But it couldn't control...
Hi I would like to confirm which NRF51822 models are the 0.35mm thin WLSCP package. I checked Avnet distributor and they say that NRF51822-CTAC-R7 is 0.35mm but the package...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
I need to make an android custom app (with UART functionality) so that only...
I'm trying to get a third party demo application working and I seem to be having an issue with the nrfx_spi_xfer function getting stuck waiting for the NRF_SPI_EVENT_READY...
Hi everyone,
I'm learning about proggram the nRF52840 dongle and I tried to code an interruption. Press the SW2 to turn on a LED
So, looking at this code, where did...
