Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I have a customer request regarding ISP1507 module (with nRF52832 integrated) and battery information.
Customer want to have battery information using LED (bicolor...
Hi,
We are using nRF51822, SDK12.3, pca10028, S130 with "Red Bear BLE Nano V1.5" board. We try also in nRF51DK and our own board (designed by us) and the issue is the same...
Hey,
I'm trying to solve the issue of connecting a central device (nRF52832 running experimental ATT MTU example) with a particular peripheral device (also, nRF52832 running...
Ever since you guys updated the site months ago, I haven't been able to post anything from a non-mobile device. I've tried multiple browsers and the only ones that work consistently...
I'm developing a peripheral with s132 v5.1.0 that supports multiple concurrent connections. I've looked at section 15 of the SoftDevice Spec and I have a couple of questions...
Dev Software: Nrf mesh sk 2.1.1 along with sdk 15 on Windows.
IDE: Segger Embeded Studio
Soft Device: s132
Device: nRF52382
Hi,
Is there a way where i can use the...
hi,
I am using nRF52832 with SDK 12.2.0 and S132 softdevice. I am faciing some issues with the memory usage. When I declared an array of size 50 bytes, my application behaves...
Hi Nordic Support Team,
I try to go to low power mode and coming back but can't at all.
I have used the example pwr_mgmt in sdk 12.3.0, but when try to use its function...
I am using the nRF51822. I am using the regulator (not the DC/DC) connection and am not using the low-power (1.2V) mode. All supplies are 3.3V.
Additionally, I am only using...
I want to make a small sensor that will wake up every once in a while, turn on advertising for a second or two and then go back to sleep again.
I'm trying to figure out...
Hello,
I've using mynewt to develop an application using the nRF52 DK (PCA10040 1.2.1, IC marking: N52832 QFAAB0 1701FH). I've been using their basic hello world application...
Hi,
I would like to update advertising packet, but every time I get error NRF_ERROR_INVALID_STATE in function sd_ble_gap_adv_set_configure(). I set all parameters properly...
Hi,
I am connecting the nRF52832 UART (on my nRF52 DK) to an external device, which by default uses 9600 baud rate (but can be reconfigured differently).
In the case...
