Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
hi
i read in earlier questions on the devzone that nordic offers to review the schematic and layout as well as perform tuning free of charge to their customer. Is that still...
Hello every!
I am testing FATFS example with nrf5284 PDK .
CLK - P1.15
MISO - P1.14
MOSI - P1.13
CS - P1.12
My micro sd card module work correctly with STM32 MCU. I...
Hi all,
I am Using SDK15, chipset is nrf52810 , In ble_app_uart application i have added the BLE_NUS_C and TWI application code , before this i have added only TWI to ble_app_uart...
This blog describes how to set up SES (Segger Embedded Studio) for use with nRF SDK:
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
Hello, I am using an nRF51822 chip, configured to run as a SPI slave. The device receives commands from master, sends commands out of the radio, and relays back RF payloads...
Hello,
I've created my own custom model which allows a client to control the duty cycle of a couple PWM outputs which are on the server. My model is quite simple, it just...
Dear all,
We're started studying payment via BLE with NRF52. But i looking for in Nordic website and google it seem a little subject and document. Can Nordic expert supply...
Hello,
I am getting really confused when using te SAADC to convert the read values into voltages.
I have seen that the example ble_app_proximity() uses the following...
I'm using 14.2 SDK SES . I'm trying to send data of sensor through BLE . When i enable Notification in mobile applicaion (nRF connect) i generally dont get any value or garbage...
Hello, I'm trying to port my code for driving spi memory (S25FL256S) from nRF51822 to nRF52840. I'm using nRF52840 Preview DK, S140 and SDK 15.0.0. On nRF51 I used custom...
Hello everyone,
I'm using PDK 52840 as Programmer/Debugger for our target board with nRF52840 chip. We have also other componen which need 2.5V voltage (down from 3v)...
I'm new to both the nRF52 family and SPI, and I'm working on an SPI master nRF52810 (using the PC10040e setup). I'm compiling using GCC and makefiles. I've set NRFX_SPIM_ENABLED...
I try to make a simple project based on a "simple message model" ( https://devzone.nordicsemi.com/f/nordic-q-a/29836/send-and-receive-a-string-via-access-layer ) with Mesh...
