Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello,
My name is Calvin and I am tasked with testing the NRF52840. I want to create my own development board for prototyping a project, but I do not want to keep plugging...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
I have a project that I need to use most of the GPIO pins available on the nRF52840 DK. I'm using SDK V17.
I'm writing a test program that toggles all GPIO pins on an nRF52840...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
Hi, We are trying to get our nRF54L15 running, but are running into clock issues. The hardware is configured without an external 32kHz crystal, so we want to rely on the NRF54...
Hi, The Kconfig fragment CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU is awesome to quickly get BLE OTA working. However, when going in depth, we can see that it's implying:
...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
Is there any documentation around the process to disable the Debug Access Port on a nRF54L device in software (not nrfutil)?
The nRF52840 has this nice documentation page...
