Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi，I would like to know how it works when reconnecting after a timeout disconnection，I didn‘t find the answer after reading Bluetooth 5.4 specification.
Hello,
I'd like to download the latest MDK for SES - links here appear to go nowhere: https://www.nordicsemi.com/Products/Development-tools/nRF-MDK/Get-Started?lang=en ...
Our design has an nRF5340 with a 32 MHz high frequency crystal and an accurate 32 kHz external rail to rail clock chip (+/- 5 ppm @ 25 C). We would like to measure the actual...
Greetings,
I am facing a problem making my BLE device change its advertising name by parameter received from UART. The advertising name is generated using my function...
Hi,Team,
I am developing ble using nrf54l15-dk.
My goal is to get the ble identity address of the device, but I don't know how to read it.
I found " bt_addr_le_create_static...
Hi,
I'm integrating a VCNL4010 over an I2C connection via an nRF52 DK.
Noting there is a Vishay VCNL4040 sensor driver, has anyone written one for the VCNL4010? It...
Hello Team,
I am currently experiencing difficulties connecting my nRF7002DK to AWS IoT Core using the aws_iot sample in nRF connect SDK v2.9.0 , which I have adapted with...
Hello everyone,
I have a custom board with an nRF5340, which currently uses the internal clock. Im using toolchain v2.9.0 and SDK 2.9.0.
I'm trying to use the RV8263-C8...
I have tried building the nrf example projects and they build fine. But this project gives this error.
The version I am using is SEGGER Embedded Studio for ARM Release 7...
here is 2 question for this example. (v2.9.0) as i looking for this example, there are some limitations like belows.
One BIG, one of the two BIS streams (selectable...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I am developing a proof of concept project using Wave share BLE400 module and the final product of this project should work on button battery backup for years. so essentially...
Hi, I recently upgraded our ncs SDK version from 2.6.0 to 2.9.0 for a custom matter application development using an nRF5340. We also support a smaller debug app that is BLE...
When setting the following channel sounding parameters with bt_le_cs_set_procedure_parameters I am getting E: Failed to set procedure parameters (err -22) or BT_HCI_ERR_INVALID_PARAM...
Dear,
i think that the evb nrf52 dk missed the bootloader because when i push on Segger (target connect j-link), there is the message NO PROBES CONNECTED VIA USB.
I...
