Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi Nordic,
I test with nRF7002-DK and IC mark on nRF7002 is below:
N7002 QFAAB0 2252AA
Here is my test data, showing about a 3dB discrepancy between power setting...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I am working with the zephyr ZMS sample application. I am using SDK 2.9.0, and I built the application for the nRF54L15DK (nrf54l15dk/nrf54l15/cpuapp). The sample works...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
I have finished developing an application, utilizing the nRF 9151 DK, and I am now working on transferring the firmware to a custom board and testing it. However, when creating...
