Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Currently using NCS v2.9.1 nrf54l15/cpuapp custom board derived from nrf54l15dk, customization to de added after solving the issue below.
The project is successfully compiled...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
I'm getting the warning about CONFIG_BT_CTLR, but I've gone through and changed to HAS_BT_CTLR. I do have the following:
# Maximum Transmission Unit config
CONFIG_BT_GATT_AUTO_UPDATE_MTU...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
Hello,
I use SDK v2.9.0 with nRF52840 and my application is based on peripheral_uart example.
Have I understood correctly that nRF52840dongle has preloaded (by Nordic...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hi,
I am almost done with my code for channel sounding with multiconnections. It all works, but somethimes i get this after a certain period of time: This Warning pops...
Hi,
I would like to know if nPM1300 supports an input voltage of 4V for Vbus. According to the datasheet, the recommended operating condition for Vbus is from 4V to 5.5V...
It seems BLE stops advertising after the first connection. Is this expected behavior? Should I restart advertising in my "connected" connection callback?
prj.conf:
main...
We have firmware that works great on the nRF7002-DK board, but now that we have our own board with a Fanstel Wi-Fi module it appears that the Wi-Fi hardware is not responding...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
Does Zephyr support automatic reconnection of the Wi-Fi if a connection is lost? I can't find any documentation on this, or code examples. It seems like every example connects...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
