I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello! I am useing nRF52832 with custom-made board.
SD 5.0.0 and 14.0 SDK
I am using modificated example of "ble_app_template", i added simple custom service from example...
I'm using USB based DFU on Windows and on Linux 18.04 LTS VM on Windows.
Platform: nRF52840-Preview-DK
SDK version: 15.0.0 (nRF5_SDK_15.0.0_a53641a)
example USB Secure...
Hi everyone,
I was just going through the library functions provided here in this link : nordic functions twi
But inside all these functions ,there is this parameter...
platform : nrf 52832 SDK : 14.0.0
I used gpiote to detect sensor's interruption . there are two sensors ,so I configure the gpiote like this :
neither of the two sensors...
Hello, I want to ask if is possible connect nRF51 Dongle in Shield Host USB ( https://www.electrofun.pt/usb-host-shield-android-arduino ) with arduino .
Thanks very much...
Hi!
My design has to be tested at 50V/m according to MIL-461F. Are there any experience with this high field strength or the MIL-standard? I want to avoid the cost of shield...
We are currently going through certification and have had an interesting failure during radiated emissions. When in normal transceiver mode, all is well, but when we put the...
Hi all,
I am using NRF52832 QFAAB0 with SDK 14.1v . Am not configuring any peripherals and just using the BLE stack in my application. During the power_manage() call the...
Hello,
I tried to port my projekt into SDK 15.0.0. During the compilation process I often get the warning:
Warning: The header file 'cmsis_iar.h' is obsolete and should...
I've read this tutorial: https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
And also Bluetooth CSS, Part A, 1.2,...
When using uart example on my curstom board, from /examples/peripheral/uart ,at baudrate 9600, bits are read with a little offset - so that starting from 4th bit, it is mistaken...
I am trying to communicate with iPhone X using Nordic_Uart sample project in SDK 14.2.
And I check the Protocols between nRF52DK and iPhone X by using Ellisys Bluetooth Tracker...
Hi,
I'm using nrf52840,
I'm using SDK 15.
I can see that in nrf_drv_power_pof_init function only few power setting are allowed - is that true? can I only use those values...
Hi all,
I have a NRF52DK acting as a peripheral and running the ble_app_uart example. I want to have bi-directional communication with a mobile device that is connected...
