Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
1st problem:
There are some failed case when i run \v2.9.1\modules\bsim_hw_models\nrf_hw_models\tests\zephyr_apps\54_aar_ccm_ecb\src\test_ccm.c
2nd problem:
If I...
Hi,
I really like the new Zephyr conn_mgr, it is really easy to use, almost UNIX like. I am wondering what is now the best way to control PSM. Will CONFIG_LTE_LINK_CONTROL...
I have a timer int callback like this:
void pwm_all_handler ( nrf_timer_event_t event_type , void * p_context )
{
if ( event_type == NRF_TIMER_EVENT_COMPARE0) {
...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hello everyone
I need to install Nrfutil offline, computers may not have access to the internet, i follow this istruction and prepare the offline directori whit the comand...
Hello everyone!
I have a question about flashing firmware to a PCBA with the nRF54 and nRF91, or any dual MCU board in general.
When looking at the Thingy91(x) this...
Hi everyone,
I have a custom board using the NRF9161. Its hardware is loosely based on the design of the Conexio Stratus Pro and I’m using the Stratus board definitions...
Hi Team,
We are using nRF9160 modem and SDK 1.7 version with Segger Embedded Studio.
Using at_client sample code, observations as below.
1. Tried to read APN configuration...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Hi,
Is there a way to reset the uptime after doing a reboot? Rebooting the device by resetting the power does reset the uptime, however we need a way to initiate the reboot...
Hi there,
We have a device that utilizes an NRF52840 chip. Several threads on DevZone - including this one and this one - warn about the dangers of applying voltage to a...
We’re migrating from the nrf52833 to the nrf52840 and noticing some major differences in how they react to being connected Via USB . Our VBUS and Data lines are connected...
I am using the nRF54L15 and SDK 2.9.1 in VSCode.
I need to know the microseconds since start throughout my code.
I created this function:
The problem is that CONFIG_SYS_CLOCK_TICKS_PER_SEC...
Hi,
I've run into a problem where a codebase build for NRF52840dk and NRF5340dk boards successfully but running it on the NRF5340 results in logs not working.
I have included...
