Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
We are programming our nRF52 based boards through USB via the P20 connector on a Nordic nRF52-DK board. However when there is a problem with our board, e.g. if it did not...
Hi,
I am working on an application using NRF52810/NRF52832 without Soft Device (I don't need BLE for this app), on a custom board. I am using the SDK15.
There is no external...
Hello,
I run the example given in SDK V15.0.0 to measure Vdd of nRF52-DK:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE(NRF_SAADC_INPUT_VDD);
I don't change the default...
Before I explain my issue I wanted to be sure on my basics, so here is my understanding after doing the research in nordic devzone
I'm using nrf52832 with sdk15
1) BLE...
I am using nRF5_SDK_15.0.0_a53641a.zip to create an application needs paring and bond. Now I got a problem that, if a smartphone removed the bond manually in its phone settings...
Hi
I’m using NRF51822_XXAC + s130_nrf51_2.0.0_softdevice, my program work well most of the time, but it dies at 0x000006b0 sometimes. Since I used the S130 softdevice, the...
Hello, guys,
I develop 52810 with sdk 14.1.0, i need the OTA features,
but i couldn't find the dfu demo( ble secure dfu bootloader and
buttonless dfu template app , pca10040e...
Hello,
As we know that nRF52840 SoC supports Bluetooth 5's 4x Long Range and 2x Data Throughput.
How different PHYs for these features (2 Mbps PHY and 1 Mbps Coded PHY...
Hi,
I am using nRF52832 to design a mesh system, starting with light.
Everything is fine, and development is reaching the end.
Before today, I use only one model,...
Hi there!
I had some great help on my last article about getting started. I'm now using Segger Embedded Studio and the nRF SDK Version 15.
Before I get too deep into BLE...
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
In the example, I see that I should use the ble_app_blinky...
I get a BLE_HCI_CONNECTION_TIMEOUT error when I use NRF connect to connect to my dev board only when my dev board is using SD 6.1.0.
Once I get the error I have to reset...
