Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello Team,
I am currently experiencing difficulties connecting my nRF7002DK to AWS IoT Core using the aws_iot sample in nRF connect SDK v2.9.0 , which I have adapted with...
Hello everyone,
I have a custom board with an nRF5340, which currently uses the internal clock. Im using toolchain v2.9.0 and SDK 2.9.0.
I'm trying to use the RV8263-C8...
I have tried building the nrf example projects and they build fine. But this project gives this error.
The version I am using is SEGGER Embedded Studio for ARM Release 7...
here is 2 question for this example. (v2.9.0) as i looking for this example, there are some limitations like belows.
One BIG, one of the two BIS streams (selectable...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I am developing a proof of concept project using Wave share BLE400 module and the final product of this project should work on button battery backup for years. so essentially...
Hi, I recently upgraded our ncs SDK version from 2.6.0 to 2.9.0 for a custom matter application development using an nRF5340. We also support a smaller debug app that is BLE...
When setting the following channel sounding parameters with bt_le_cs_set_procedure_parameters I am getting E: Failed to set procedure parameters (err -22) or BT_HCI_ERR_INVALID_PARAM...
Dear,
i think that the evb nrf52 dk missed the bootloader because when i push on Segger (target connect j-link), there is the message NO PROBES CONNECTED VIA USB.
I...
Hi,
We are currently in the process of evaluating the nPM1300 PMIC for our project and I would like to know if there is a way to supply Vsys using the battery even when...
Hi, I'm in India Using JIO 4G sim card in India can't connects to NB-iot . Here network provider supports NB-iot but if i try to connect the network it is searching for a...
Hello,
I have always been able to use VSCode to find various installed toolchain versions, but today I suddenly cannot find toolchains other than v2.2.0.
I checked and...
Hi
I have a beacon sending out some data, and I have already finish the TX side, I also want to have a RX side to receive the data, in addition, as there are many other...
GNSS not working on Thingy:91 after modem_shell flash — help and gnss start return ERROR
Device:
Thingy:91 (NK-THINGY91) RS Stock No. 196-3901 nRF9160 + nRF52840 combo...
Hi Nordic,
I’m new to the nRF Connect SDK for VS Code and currently evaluating the nRF7002 DK board. I’ve been able to build and debug firmware successfully for the NRF7002DK_NRF5340_CPUAPP...
