We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello, I've been working with a custom board using the nRF5340, but I’ve been struggling with picking up any BLE signal from it. I flashed the network core separately with...
I just got my custom board in and when the code gets to bt_enable it returns -11, but on the DK board it works fine (using the same board dts files and software for both)...
I am implementing DFU using my own transport to retrieve the binary image from AWS.
I'm developing in 2.6.0.
I am using the DFU TARGET libraries.
When I start my download...
Dear Nordic
I'm looking for a DTM code for nRF54L15,
From previous experience of nRF52,
There are some example HEX files available in SDK,
But I can't find any example...
Hi,
I have used the sample given in blog , however, my purpose is to get data from two device "IMU1" and "IMU2", using callback " static uint8_t ble_data_received " to print...
Hello everyone! :)
I have a problem with LTE connection. It worked for a few months; however, since a few days ago, the nrf9151 refused to connect to LTE. I tried with 2...
I'm building a system with onboard stereo speakers that can take a maximum of 1,4A when operating at low battery voltage. Can I safely bypass the npm1300 and directly draw...
I am using nRF Connect SDK 2.9.0 with Toolchain 2.9.0 and trying to interface Winbond W25Q32 SPI flash memory with nRF21540DK (nRF52840) . I need help with the following:...
Dear Sir / Madam,
We are testing with NRF9160 and building on top of k _uptime _ticks, I find the precision of the ticks clock to be ~70 ppm, while testing on my desk. According...
Hello,
I have been trying to figure out how to enable coexistence between Bluetooth low energy and the nRF7002 and I have some questions.
1. In the nRF Connect SDK documentation...
Using nrf5340dk, SDK v1.9.0
Want to add external RTC via I2C to wake mcu up via alarm, Facing Issue with I2C init.
I have gone through the suggested sdk fundamental course...
Hi,
When do you plan to update your Online Power Profiler Tool for cellular with nRF9151 device?
I just can see nRF9160 available for calculation.
Regards,
Hello,
I am working on an ESB (Enhanced ShockBurst) communication setup using the following hardware:
Receiver (RX): nRF5340
Transmitter (TX): nRF52840 MDK Dongle...
I would like to add smp ota firmware upgrade to the matter sample project, can you provide me with the specific steps to do so, and in which path is the ota file compiled...
