i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I want to save Power by disabling the SD Card. VCC of the card is already regulated with an external MOSFET switch and controlled by a pin of the nRF. The problem now is,...
Hi,
I'm currently using SDK 14.2 (on 840) and SDK 15.0 (on 810) with the UART example.
I'm trying to implement the following system.
The Device only receives data...
Hi all,
I'm using SDK 15, nrf 52840, win 7,
The USB cdc example works fine for me.
Yet, when I moved the code to my project the driver is not set by win 7.
On device...
hi Support Team
I am working on Asset Tracking project.Looks like Bluetooth Mesh is more oriented towards controlling.
I have a Ble device Emitting some Data. (say A)...
Hello there,
I have developed simple coap client and simple coap server based firmwares on nRF52840. My hardware/software configuration is:
SDK: nRF5_SDK_for_Thread_v0...
Dev Env
- SDK: v12.1, SoftDevice : S132 v3.0.0
- NRF52 start program : ble_app_uart_c
1. Is it possible to connect to NRF52832(Central Mode) from Android(Phone Pheripheral...
Hi,
While using sniffer and wireshark, I find the issue below.
CRC value of the raw data and the decoded are not the same at all ?
I find this with nRF5_SDK_15.0.0...
Hello!
I have some problem to generate the right service.h file with nRFgo Studio. I used the help in nRFgo Studio and tried several configurations. Sometimes I could connect...
Hi,
I am facing a frustrating problem in my project: I am using Nordic nRF51822 running on UART application SDK 11. The problem comes to when I add peer management and DFU...
Hi,
I am trying to build the connectivity firmware for a custom dongle based on the nrf52832. I am getting a section overlap issue when I am trying to build the solution...
Hello,
I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some...
hello Nordic Team
I am using 2 DK
One with Light Switch Proxy Client
Another with Light Switch Proxy Switch
I am using Mobile Mesh App 1.0
Client Provisioning I...
I have been trying to use the nRF Connect app on my Apple iPhone in order to get the Current Time Service.
I bought a Arduino Primo that has an nRF52 on it.
The example...
I am working with an nRF51822 IC revision 2 chip and S110 SD 6.2.1 with Keil 5.10. My version of Keil 5.10 will not recognize the chip. I think that this is because I cannot...
Hi,
I am using nRF52832 microcontroller in project.
I use SPI interface for serial EEPROM.
I could able to see write packets are getting transmitted and verified the...
