Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hi, I tried to start toolchain manager on my main computer and its not working anymore. I tried to delete all nrf related folders, deleted all apps including nrf connect deskop...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
Dear, I'm developing on nordic 52840 with ncs2.6.1.
I found that the Current will reach to 600+uA in k_sleep state by enable SPI in device_tree and if i disable the spi...
Hi,
I send "chat private 0x0028 hi" over a serial terminal, and the MCU restart because of overflow, please see error log as below picture.
I tried to modify the "CONFIG_SHELL_STACK_SIZE...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
My customer is now unable to disable secure erasure after using the APPROTECT function. Is this correct?
Please let me know if there is another way to check this.
”nrfjprog...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Hi team, We’re using the STM32H7 as the host MCU and the WMC02C Wi-Fi module (based on the nRF7002) connected via SPI on a custom board. I tried running the Wi-Fi scan example...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Hi
We are migrating from Segger Embedded Studio (SES) to VS Code for developing in the nordic connect SDK. We are using the RTT logger for debugging our device. In SES you...
Hi Nordic,
I test with nRF7002-DK and IC mark on nRF7002 is below:
N7002 QFAAB0 2252AA
Here is my test data, showing about a 3dB discrepancy between power setting...
