I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello! I'm looking for a way to include fast charging capabilities in my product, while still allowing USB2 data to pass between any host PC and the nRF52840. As I understand...
Hi, I have custom board with nrf54l15. Im using sdk 2.9.1 and nRF54L15-DK as debugger/flasher. Im able to flash firmware correctly using SWD, or do nrfjprog --recover, but...
According the nPM2100 page "nPM2100 comes with exceptional software support for Nordic’s nRF52, nRF53, and nRF54 Series" but doesn't mention "nRF91 Series".
Currently I...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I need both zephyr power device management and the low power features of LPUART in my project.
However, enabling PM_DEVICE raises idle current consumption by quite a bit...
hello to all.
i been strugling the last couple of days to make a simple PPP connection from a debian12 laptop to the internet passing trough the nrf9151. I followed the...
Hi,
I want to produce a pulse with 4 seconds length from p0.25, but i am failed.
#include <zephyr/sys/printk.h>
#include <nrfx_pwm.h>
#include <hal/nrf_gpio.h...
Hi, I would like to have some suggestions on my PCBA design for nrf54L15 chip. Please review it and give some suggestion moving forward. I am making this PCB to use this with...
Hi,
We are working with a custom board that uses the nRF54L15 and I seem to be getting a lot of errors (but not always) related to memory access error when flashing the...
Hi team, After executing RRAMC.ERASE.ERASEALL with an external debugger, I was unable to access the CPU (board) after reset. To resolve this issue, I connected the nRF-programmer...
Hi,
We need to develop a Windows APP to achieve DFU and battery check with nRF52832 by Bluetooth. Does Nordic have DLL that we can use? Or do you have suggestion for us...
Hello all, First, thank you for the support and community here, which is very helpful. I have been developing a device using the XIAO nRF52840 device. (link: https://wiki...
Hi Nordic team,
I'm working with the nrf5340_audio source code from the nRF Connect SDK and have compiled the project as a gateway. When I try to connect to a headset, I...
I am trying to create a partition on mx25r64 using partition manager on my nrf52840dk. Below is my overlay file
Below is my prj.conf file
Below is my pm_static.yml file...
Hi,
I configured for using security BT_SECURITY_L2 for a device that I had previously configured for using BT_SECURITY_L4. When I try to connect with an Android phone that...
