I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello,
I am starting from ble_app_multilink_central example in SDK11.
Per the comment, when updating the number of central links, RAM setting should also be updated...
Hi,
i am using pca10028 with S130v2
We'd like to use a couple of services as we have to deal with a number of external interfaces.
Sadly we cannot get more than 4 services...
Hi there,
I'd like the ability to hold some data locally then resynchronize once the central reconnects.
Are there any example projects that demo this?
What is the...
Hi,
i am not able to send (write characteristic) from android at a higher transfer-rate than 2.3 kbit/second.
With another Bluetooth LE peripheral i get more than 100kbit...
Hi all, i have a nrf51 Development kit and a nrf51822 smart beacon kit and I want to read them in Matlab using the bluetooth receiver of my laptop. I used the instrumentation...
hi all
i try to write in volatile memory but after the second (the first is ok) writing the nrf8001 response me with 0x84 0x08 0x81 -> Internal Error
i don't know why
please...
Hi, apologies for my ignorance but I'm confused by something. I'm looking to add a PA and was thinking of using the RFAxis RFX2401C like many of those nRF24L01+, PA and LNA...
Hi All,
Please tell is ble mesh is it work for nrf51822 EK, the code is taken from this link: github.com/.../nRF51-ble-bcast-mesh . the code provided in this link, is tested...
We have made a bare minimum prototype with nrf51422 QFN chip following the reference schematic for internal LDO setup in 11.5.1 section of nrf51422_PS_v3.1. It is built on...
Hi,
Am using NRF52 S132 softdevice,
I have a use case like when I press a button , I should turn off BLE. So I enabled an interrupt for button. Whenever this button is pressed...
Hi,
i am using nrf51822 to develop our product. I'll try to describe more details to make you understand more clearly.
STEPS:
While testing my project, I had...
Is it compulsory to have same Baudrate on central & Preipheral side when using the NUS..?
I'm using Central @ 115200 & Peripheral @ 9600 [No flow control on either].
...
Hi,
I've written an app on the nrf51822 (rev2), with S110 (v7.3.0) and SDK v6.1.0. I've written a custom non-blocking UART driver. I'm running into an issue where the UART...
Hi,
Using the nRF5 11.0.0 release SDK, I'm trying to set up one task to transmit to and one task to receive data from the UART. Nothing special.
The configuration block...
Hi,
The xQueueReceive function in FreeRTOS seems to be broken, when a non-zero timeout is specified.
Example, I'm trying to create and ordered output mechanism for the...
