I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hello,
I tried the example ble_app_multilink_central (SDK 11.0) with S130 soft device. My requirement is that nrf-dongle should work in central mode and it should connect...
Super general question :)
Our current products use nRF24 chips (paired with 8bit AVR's) and we're very happy with performance.
For us the key requirements are low latency...
Hi all, i am trying to load this example on the smart beacon kit; i followed this guide step by step ( devzone.nordicsemi.com/.../) but the problem is the if i load the precompiled...
Hi all, i want to use the internal bluetooth of my laptop to receive values of a sensor on the nRF51 DK, and save them in a text file. How can i do this?
Hi, In my project I am using the signed bootloader example. The issue I got if I generate .zip file for dfu without --key-file the with --dfu-ver is option is working fine...
I have up and running the serialized ble_app_hts using ser_s130_hci serialization on two BMD-200 evaluation board of Rigado.
Now I want to know what files I have to use...
When I input the command below:
nrfgocli -p <path_to_application.hex>
it gives me the error below:
Could not connect to board
ERROR: Could not connect to board ...
I've migrated over my application code. I've noted that SDK10's new modules causes much high RAM consumption than on SDK 6.1. Everything is working however, except for the...
What are the correct parameters that I need to set in uVision to compile the experimental (signing) DFU for NRF51822_xxAC (SDK 10) (using dual bank)
Xtal?
IROM1?
IRAM1...
Hi Nordic Community,
Could you please tell me what is the antenna reference design used in the nRF51 DK? and why a lot of BLE development boards (like Redbear BLE shield...
Hi everybody!
Im trying to implement slave spi to bluetooth bridge.
In short, when cs line goes low, i want that one handshake line automaticaly go in busy (high) state...
Hi,
I'm using the nrf52 and in my application I need to sample a sensor after applying an IR pulse; the pulse length influences the sampling thus cannot be disturbed by...
I think this is a rather common problem:
I want to expose a couple of variables from my model code (members of structs) as characteristics. Is there a simple and elegant...
Hi
Question
What is the risk/chance that future revisions (>2.0.0) of S130 will be incompatible with the setting UICR.CLENR0 = 0x1C000 ?
Background
Today we would...
Hi,
I need to wait for a period of 7.5ms whilst my I2C sensor completes a measurement, I am currently using the nrf_delay_ms function however I am looking to optimise the...
