I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi
I have been working with the nrf52832 breakoutboard from sparks fun and the nrf52 10040 Dev board.
I want to work with SPI communication in order to intergrate an accelerometer...
I'm having an issue with some iPhone11's, where under certain conditions the iPhone11 is sending two consecutive Link Layer requests with a Control Opcode of 0xFF. The SoftDevice...
Using zboss_start_no_autostart() instead of zboss_start() will cause a power consumption of 630uA. I was expecting the device to be sleep and in a very low power mode.. All...
Hi
When I use the nRF5_SDK_15.3.0, the nRF52832 cannot enter low power (about 900uA). The example is file ble_app_blinky.
The main code is as following:
int main(void...
Hello,
I want to blink the LED by pressing button on nRF9160dk. Is there any sample available to start with?
I started with button demo but on button press there is no...
Hello,
I am using SDK 15.2, could someone please tell me the location of pstorage.h file in the folder. (I found pstorage._platform.h but I cannot locate pstorage.h.)
...
Hi nordic,
I am developing with nrf52832, s132,v15.2,0.I am using secure dfu bootloader. But its connecting in nrf_connect app, after connected, i got this below mention...
Hi,
I'm wondering if you will support sending data using control plane (CIoT EPS Optimization using CP) and Non IP Data delivery for CATM . I assume you will do it for...
Hi:
I am running the example program ble_app_att_mtu_throughput on the SDK52 for the NRF58232 and the NRF58340 next.
My question has to do with how to modify the example...
I'm trying to simplify the open_bootloader example from SDK 15.3. I'm getting rid of version, signature and keep only the CRC validation. I'm actually trying to understand...
Device: NRF52832_xxAA Softdevice: S113 v7.0.0
Hello.
Sometimes, during firmware running, I get a fault from Softdevice with pc: 0x0001A990. Could you inform me what causes...
When I send 90 KB data via BLE. Sometime I am getting NRF_ERROR_RESOURCES error. I have tried all the things that are available in support site. I am reading data from SPI...
Hello Forum,
I got a Thingy:91 today and of course I wanted to test it immediatelly), but I wonder:
Is the nrfcloud.message simply because of no LTE-NB1 network / roaming...
We are migrating BLE application code from SDK-12.3 to SDK-15.3.
Our firmware uses SPIS module. Now in the example code I could see
NRF_POWER->TASKS_CONSTLAT = 1;
What...
