I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
Hi,
I am stuck in sending and receiving serial data over Rx and Tx in nrf51 DK. I used arduino to prototype a fingerprint access control system. Now I am shifting to nrf51...
Hi,
I would like to know if the LFCLK is enabled after zboss_start(); and after zboss_start_no_autostart().
I would like to use an rtc event to trigger a PPI routine and...
Question: for the nRF52840, if I configure a GPIO pin as an open-drain output (DRIVE setting of S0D1) and then select this pin as a UART transmit pin, does the open drain...
1 .after the flashing the board i get a Zigbee Connection and Bluetooth connection but i can't able to control the bulb by using both board and bluettoth
2. Sir i am using...
Dear all.
I know the nRF52840 has 2 uart module.
I've been used only 1 uart setting like below pin connecting in 52840 DK reference doc.
But now i have to use 2...
*** Disclaimer *** I am a total rookie on this technology *** Disclaimer***
I'm working on a small BLE proof of concept and I have an nRF52840DK board. I've got Wireshark...
Hi, guys! I'm using the nRF52 SDK 15.3 BLE_APP_UART peripheral example.
I wish to add 3 ADC channels (12-bit) to read 3 potentiometers at a sampling frequency of 6kHz. ...
Hi,
I've BLE custom data sent to nrfcloud and looking for ways to plot data. I've used "add custom card" from configuration to extract data but was not able to plot/view...
hi, I am working on nrf52832 platform and tested some Bluetooth examples of SDK_15.3.0, I want to test some Bluetooth examples like audio, media and etc, is there any project...
Hi,
I am using a BLE master to bond with nRF52832. SDK is 15.3.0. Both side support secure connection.
I have tried to set the address type of master to public or random...
Hi, I'm starting to use the nRF52840 DK, I have downloaded the segger embedded studio but I don't have idea how to start, I need a sample example to use the pins to control...
I am new to Nordic products. I have a custom nRF51822 board and I want to flash it with Keil uVision and ST-Link V/2.
As I understood, I have to program the SoftDevice firmware...
I'm implemented DFU (with custom transport, but the problem is not there). Even when flashing SD+bootloader+app+settings I can see an error in the logs:
```
14:23:48.096384...
NRF Connect sees the devices no issues and connect. When it comes to running any of the examples in the toolbox, the devices are never seen. Location services are allowed...
