When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi! I've been working with the Thingy 91 and I've found that the SIM card was running out of data, so we decided to buy more data to keep working. The board was working as...
Hi,
I'm making a new design. I want to use the NRF52840. I also want a low power microphone interface.
PDM seems like a good idea, modern PDM mics have low power modes...
Hei
I've gotten the ipv6_coap_server example to run on the nRF51-dongle. I got the bt0 interface after connecting to the device and I am able to ping the device.
My...
Hi all,
Previously I spent some time to set up the nrfsniffer and with support I had succeeded; devzone.nordicsemi.com/.../setting-up-the-nrfsniffer
However as I have...
Hi
I want to modify the nrf9160 software samples from Nordic so I can use float with printk() and sscanf() functions.
I am also using gcc.
I try figure out how/where...
Hi,
As a part of FCC testing, I am trying use the following radio_tx_sweep_start(txpower,uiMode,channel_start,channel_end,delayms) with below parameters.
uint8_t txpower...
Hello, I have seen and heard of nrf52 alot that it can be used as payment card by using HCE technique. Can anyone please shed some light on it ? I want to know the way we...
Hi,
I'm running a nRF52832 connected through TRACE port to a Segger J-Trace Pro.
Some traces seem to be lost, and Segger support team tells me it is possible as nRF52832...
I have a few questions regarding AoA mode.
My goal is to append the CTE frame too a standard advertisement frame. I would like to use one of the following examples as the...
Hardware: nRF52840, running on dev kit PCA10056
Software: SDK 15.0.0, no soft device
I'm trying to get the POF comparator working, and after struggling in our product...
I just updated my project from SDK 15.3 to 16.0. I am using the nRF52840.
I am not receiving the APP_BUTTON_RELEASE event when waking up from a button press. It used to...
I am trying to the asset tracking application on nRF9160DK and following the steps mentioned in https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hi there,
I have tried to build mqtt_simple but ı got an error says:
#error bsdlib must be run as non-secure firmware. Are you building for the correct board ?
I am...
Dear Support Engineers
I am in the process of designing the automated testing platform for a 52832 based device and would like to test to make sure the components/devices...
