Hello Nordic team,
We are reviewing our nRF54LM20-CAAA (CSP61) hardware design and would appreciate your clarification on several power and RF related points.
DECRF...
Dear Nordic Technical Support Team,
I would like to inquire about the following regarding the nRF54L series development:
Can I develop for the nRF54L series using...
nRF Cloud — CoAP transport (device shadow) Date of incident: 2026-06-22, ~13:04 UTC — still unresolved at 20:42 UTC (7h38m+) Device: nRF9151, modem firmware mfw_nrf91x1_2...
We are doing a DFU over BLE with the second MCUboot partition on an external flash. Some times Zephyr can't access the flash after booting, resulting in a bricked device,...
Hey, I am trying to implement ecdh key agreement and derivation, but I am getting PSA_ERROR_INVALID_ARGUMENT (-135) from psa_key_derivation_key_agreement: Any idea what is...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
I am using nRF54L10 with nRF Connect SDK v3.1. The device connects over BLE, wakes every 30 minutes to read sensor data, and then should enter deep sleep (System OFF). However...
Hi there,
When using a PIN as RESET, what is the minimum activation time required to insure a reset?
I thought this should feature in Table 16.10.3 but I could not figure...
What is the logger message pool? There are two main definitions for it:
NRF_LOG_MSGPOOL_ELEMENT_COUNT
NRF_LOG_MSGPOOL_ELEMENT_SIZE
However it is not clear what it...
Hello ,
I want to use the NVIC to manage the interruption of the accelerometer and to run a specific program, are you ideas about the possibility of this?
Best Regard...
hi,
I am using nrf 52 DK and softdevice S132,PCA10040 board . I need to toggle a pin,set a pin,reset a pin .can anyone take this ticket to a sample code/ code snippet and...
Hi,
I have a project with 52810 which I use rc for LF clock source and I need use P00 and P01 as general GPIO, I have set both CLOCK_CONFIG_XTAL_FREQ and NRF_SDH_CLOCK_LF_SRC...
We are developing an nRF52832-based circuit with 1.8v power supply, which features BLE, NFC, SAADC, I2C & SPI.
According to datasheets, all 3rd party components are also...
Hi,
we plan to use the nRF52832 for a new project, I have two questions:
LE secure is supported, is this right ?
We want to pair up to 8 phones with our device....
Hi,
I am using SDK 14.2 with nrf52840 board. In my project I am using USB and BLE together. I have noticed that when I enable the LE Secure pairing and after that my USB...
Which nrfutil version should be used with Mesh SDK?
Getting started for Mesh has the link to nfrutil verison 0.3.0.0. In pc-nrfutil github repo the latest version is 3.5...
Hi!
I try to do simple led blink on nrf51822 and after build i got this:
Checking project status
Building ‘dongle’ from solution ‘dongle’ in configuration ‘Debug’
Compiling...
Hi,
I am using Segger IDE and now I wanna to use the temperature sensor presents in the PCA10040 board.
I tested the SDK example using the keil and works fine. When I...
I have your NRF52 DK and beacons.
I want to make the case so that my Nordic NRF52 DK will get data from Nordic beacons and forwarded that data on the UART port of PC....
Hi there,
I am developing a BLE dongle, and a BLE peripheral both based on NRF51822QFAC. The BLE dongle scans, connects, and disconnects the BLE peripheral by UART commands...
Hi
I get the following compiler (assembler) error in my project:
... Compiling file: hardfault_handler_gcc.c /tmp/ccstUNqW.s: Assembler messages: /tmp/ccstUNqW.s:46: Error...
Hey All,
I'm using the nrf_drv_uart UARTE driver (NRF52832) communicating with an external device. The UART init code is executed using a function (call all_main in this...
