I am doing some development on nRF5340 and I experienced MPU faults. We tracked down the root cause and this led to a PR https://github.com/zephyrproject-rtos/zephyr/pull...
I compiled some legacy code (once written for the nRF52832), trying to adapt it for the nRF52805.
I have already done the following:
defining -DNRF52805_XXAA
defining...
Hi,
I'm working on a project where I need to sample an ADC with an accurate sample rate. It essentially works except that I do not get the correct rate from the timer...
Hi,
I’m observing an issue in a Zigbee network where, after several hours of correct operation, the routers stop retransmitting the NWK broadcast frames sent by the coordinator...
Hi,
I am trying to program a custom board containing an nRF9151-LACA using the external programming interface (P20) on an nRF9151 DK. The board has never been programmed...
Hi,
I’m reviewing the release notes of the Zigbee R23 add‑on , and I see that the compatibility table maps each add‑on version to a specific NCS (nRF Connect SDK) version...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi everyone,
I'm currently working on MAX30100 sensor and i need to read this sensor data with i2c, currently i'm able to read mpu6050 and 9255. However i don't have much...
Hi all,
My BLE device uses the NUS profile to send data to a connected smart device. At the same time it should also be possible to connect to a RPi/Linux based gateway...
I now use nrf52832 to do development, nrf52832 and mobile phones to transfer the data is relatively large, I would like to achieve For mobile phones that support BLE4.2, a...
Hi Everyone,
I have been experimenting around with the low power SAADC example in SDK13.
I am using PCA10040 dev board and I have programmed it to start/stop ADC sampling...
Hi,
We've been developing an peripheral HID over BLE using Nordic's SDK, connecting with iOS, Android, and Windows devices. (Board: nRF52832, SDK 14)
We've noticed an...
Using 2.0.0-1.beta on Linux Mint 18.
Have installed pyserial with: sudo pip install pyserial --upgrade --ignore-installed
resulting in:
Installing collected packages...
hi ;
now after i maked a successful connection between smart phone and nrf51822 and i could change the state of gpio pin 20 i find a new problem
i want my pin is still...
Hi All,
Just wondering if i'm doing the right thing here.
So i am using the example of the central device to get started.The idea i'm trying to do is to use the central...
Hi,
I am working on my production hardware with nRF52840 on it. I am using MBED OS. What should be the memory map of 52840 for soft device and Application code? I am using...
Here are my system requirements:
A single "Controller" needs to send 4 bytes of data per node.
There are 25 nodes in a system (100 bytes total payload).
All nodes must...
Hello,
Is it possible to use Mesh SDK and create a GATT database for mobile device to connect to? There are no examples for this in Mesh 1.0.0 and 1.0.1 except a simple...
Devzone,
I'm working with the nrf51822 dev kit- specifically with master emuator API version 2.1.8.
Does this current release of the API (2.1.8) or subsequent releases...
Hi Everyone. I am Anthony, embedded software engineer. Now I need to dive into the Nordic BLE world for the new project. And we are going to used nRF51822 MCU. But I have...
Hi there,
On my project I was working using sd_flash_xxx functions to write the whole flash pages or erase it, so I added peer manager to my project and I had to switch...
