I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi
i have LIS2DH working ok just having problem with the order of return values, maybe just a quick fix.
LIS2DH is running on 10Hz, low power mode, I receive interrupt...
Hi!
We are experimenting with BLE Mesh on nRF52832.
Our setup includes around 50 sensors located in a building which need to report sensor data ( 12 bytes ) in real time...
Hi,
I'm trying to configure nRF51 usb dongle as server but can't get it to advertise.
Neither 'Advertising setup..' nor 'Start advertising' option seem to do anything...
So I've been banging my head against the wall for a little bit now and this just isn't making sense to me.
I downloaded the NRF Toolbox app on my phone, and I compiled the...
I am working on SDKv14 with S132 softdevice and was trying to modify the Heart Rate Example to vary the Manufacturer Specific Data after each advertisement. After searching...
Hi,
I have recently started working on nrf52832 chip, don't have much knowledge on that. I have two chips (nrf52832) one is running on bluetooth version 5 and other one...
I'm evaluating BT5 feature using the PCA10056 preview dev kit and SDK v15.
When working with LE Coded PHYs, is the S2 or S8 version? In the SoftDevice release notes only...
Hello,
I'm testing the bootloader with SDK v.15 and I found a state when DFU won't resume (on BLE transport).
I crashed nRF Connect randomly, in that case, between the...
Hi All,
I am designing circuit to Turn ON 4 LEDs at a time based on high and low of GPIO
Supply voltage is 3.3V my doubt below circuit is fine whether it will work fine...
I try onnrf52804 (nrf52840-DK) with SoftDevice V6.0.0
----------------------------------------------------------------------------------
ble_gap_scan_params_t s_scan_params...
Hi all,
I want to use the python scripts provided in application notes in nordic documentation to run DTM example flashed into nRF52840 SoC. So when I open command prompt...
In the infocenter, after searching for something, if you click on an item in "Search Results" (left hand panel), it brings up the associated page in the right hand panel....
Hello all,
I'm trying to do a "BLE scanner" in order to read non connectable advertisements. These advertisements can be PHY_CODED and PHY_1MBPS (classic BLE advertisements...
Hi everbody,
I'm using the BLE Database Discovery module to discover services and characteristics of a BLE peripheral. This works fine, except for one strange quirk:
When...
