I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
Hi Nordic Team,
I am working on implementing synchronized sensor sampling on multiple Bluetooth devices that are externally triggered. To achieve this, I have combined the...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
Hello, I'm trying to use BLE on nrf52833. I'm developping with segger embedded studio and I' m usign the BLE peripheral example "ble_app_blinky". Firstly I erased the flash...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
Hi,
I'm trying to connect the nrf51822 chip to an ethernet (W5500 module). For the moment, it fails without error (nothing works).
So I start from a simpliest program...
I am finding that bonds are not saved to flash when using the latest SDK and S110 SoftDevice.
To test this, I am using the HTS example code, and the Master Dongle.
I open...
Hello,
I discover and connect my nRF51822 service. It can be peripheral and Communication read/write data. but have some issue for disconnect/reconnect .When My app for iOS...
Hello,
I am planning to develop a system where there are 16 bluetooth LE devices (nRF51822) each one sending/receiving data via Bluetooth LE (~30 kbps) to/from an access...
Hi !
I know that there is a way of OTA updating the nrf8200 application. But i'm not sure if this process requires aditional hardware like it happens when using the BLE113...
Hi All,
I am able to successfully connect to nrf51822 EK using BlueZ 5.12 and can read many of the characteristics except for the temperature value.
I understand that...
Hello
I have a project about voice communication.
Trying to do bidirectional voice communication, is there any possible to work on nrf51822
It means whatever via Bluetooth...
Hi,
I have version 2.0.0 of Evaluation Kit. I was waiting for the new SDK and SD 6.0.0 but I have seen the warning about hardware versions. I have to finish a SoftDevice...
I'm a noob in this alley! it is my first time working with Nordic products. In the past I used Energy Micro and ST Micro.
I downloaded Keil 4.x from ARM website. Then I...
Hello,
I am developing a project using nRF51922 and S310, and the project is built using SDK4.2.2 with the modifications mentioned in a document called "nRF51922 - ble...
We are looking to understand the internal working of the nRF51822 firmware (MEFW_nRF51822_0.9.0_firmware.hex). If someone can share the original code or the basic block diagram...
Hi folks,
I want to match my IFA PCB antenna to the nRF8001. As Harald recommended a couple times, I am going to measure the antenna of the final PCB with a Vector Network...
Hi All,
I use the 51822 DK to do the current measurement and do as the DK user guide 5.1.8 current measurement.
I just use the __WFI() to make the 51822 get into idle...
Hi!
I must match NRF24L01 to 40+j48 ohm antenna. This is not my design, so
no possibility to change. I have PCB antenna, that was measured to be 40+j48 inside
enclosure...
I have some non-volatile storage routines that I have written before, but the new SDK V5.0.0 has this pstorage module that is supposed to replace it, right? How do I migrate...
