Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
For some sort of geofencing application, we want to include the BLE module nRF51822 into a Base Station (BS), and a small mobile device (MS).
The MS should detect the presence...
I have 2 moduls from ebay (rfinchina). I write little librarie for nRF24L01 and my msp430.
When i start my coard and init spi and try read few register - i have problem....
Hi,I use 51822 to make a fitness device. one of the function is advertising current value(Steps,Heart rate,Distance,Calorie) to the phone over BLE. What the default service...
I downloaded nRF51 SDK 5.2.0 and I am studying the examples for S120.
I notices that there's no gcc directory, thus only Keil compiler can be used. Is there a way to use...
Hello,
I have some questions regarding bluetooth low energy and the NRF51 series.
[list=1]1) I have to synchronise maximum 17 sensors, so i will maximum need 4 masters...
Hi.
I am looking for the internal resistance of the ADC pin of my nrf51822. I have looked at the Product Specifications (as well as the Reference Manual and other documents...
I find it unstable to send hid data, even if I set timer 1 every 8ms to send hid data.
I can catch data bag from wireshark it seems that interval of two data even close...
Hi All:
The hardware is working perfectly up until I changed some codes in the program and load it on the chip then I am unable to program again. The error message is:...
1.Size of EPROM. Is it big enough for our program as well as our data file for the whole day?
2.How can we secure the EPROM so that no one else can overwrite our code or...
We have an application that is an apple ibeacon, plus some extra properties that can be read (battery level for example)
The "ibeacon profile" eats up all the space in the...
Hi Guys,
i'm a newbie, trying to get the heart rate demo project working.
I've connected the nRF8001 to my own hardware, using a PIC processor.
i'm able to connect...
Hi,
I have a question about the service profile (ex:heart rate service, battery service,etc...), these services are based on protocol of IEEE11073-20601? Actually, I want...
See subject. The softdevice is currently installed on the chip (v6.0.0-1.alpha)
I searched online, and found some information that the security state of the chip has been...
Hi all,
When I receive data from the phone app, I do it via this service handler (and it works):
err_code = ble_services_init(&my_device_service, ble_receive_handler...
error:-559038737 ...line:1128 file_name:src\ll_lm.s0.c
And I can't find this file, so can somebody help?
Why this happen? How can I do to avoid this？ It will cause reboot...
