I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hello Nordic,
I am trying debugging on following project [--ble_app_lbs_master--]. During debugging, I never reach at app_button_is_pushed function. I tried pressing the...
I have built a PCB that uses the nRF51822 . I am failing to load the binary onto the chip via the nRF51 DK. I can:
connect to the nRF51822 on my mac using the JLinkExe...
Hi,all.i want to use pwm in my code.And i init pwm with APP_PWM_INSTANCE(PWM1,1),then i get an error:identifier "TIMER1_INSTANCE_INDEX" is undefined.Can someone help me ?
Hello,
We are doing a study about the features of nRF51822 and the nRF51 Development Kit and are wondering about the maximum visible "friendly name" (DEVICE_NAME?) which...
Greetings,
I am trying to get the frequency/channel matched with RSSI values using S110. Is there a way to pull it through the softdevice functions?
If not, can I pull...
I started with the beacon kit and example code. I have since added IAS and LLC services that I have mostly taken from your proximity example. The problem I am having now is...
I have burnt ble-app-multilink peripheral code on my nrf51822ek. What happens currently is dat when i press button on kit, on kit led turns on . when i press it again, it...
Is it possible to change a characteristic's security mode after it's already been added with sd_ble_gatts_characteristic_add()?
I'd like to be able to switch back and forth...
I have a new nRF52 Preview Development Kit, after connect it to a computer with a USB cable, the status light (LD5) come on, indicating it has power. However, the standard...
I am working on a project to integrate nRF51822 with a rechargeable battery,
and make it chargeable through micro USB cable.
Any recommendation on the battery model, charger...
I have a dual mode BLE / ANT+ nRF51422 design going through regulatory testing for FCC / EU marketing approval. I have previously successfully tested a very similar design...
The spec of nrf52 mentiones 'Propriatary RF' as option. I was wondering if that could be used to implement 802.15.4 which would save us an entire IC and power and like basically...
Hi there!
I would like to implement the nRF24L01-module to one project.
But, it would be great, too, if i can use the application manual to use only the chip itself with...
I have the nRF51-DK development kit (PCA 10028). I'm following the gcc tutorial here - devzone.nordicsemi.com/.../.
I'm using the ble_apps_hrs project as a basis for my...
