i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I hope this isn't a duplicate of another question. I searched on sd_power_system_off and didn't see anything exactly like this.
I'm creating a new project, based on ble_app_template...
I have the 51822 chips, and want to establish a network with large data volume, I use the S130 now, but the effect is not ideal, so I want try the BLE4.2. Do we have the SoftDevice...
Hi,
For the past few weeks I've been trying to make a small device that would simulate a mouse with Arduino and MPU6050 accelerator + gyroscope sensor. I wanted the device...
created a new BSP PCA10001 from PCA10028 and replaced the CFLAGS += _DBOARD_PCA10001 for uart example in peripheral folder using sdk 10.
Migrated simple_uart example &...
Hello,
I wish to communicate with the chip via SPI NRF51822.
The NRF chip is configured as a slave. Based on the SPi_slave_example code, I can't set to 1 the semaphore...
I configured my system to sleep after inactivity time.
nrf_gpio_cfg_sense_input(WAKE_UP, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_HIGH);
err_code = sd_power_system_off...
NRF51822 most time is in sleep mode.
Each 5 seconds it wakes up to make ADC measurements.
But adc_event_handler force only once, but I want to see it every 5 seconds.
...
I'm new to using the RTT Viewer. It was working fine (all morning). I've only been using the SEGGER_RTT_printf(0, "string %d \n",x); call to dump text and data to the viewer...
Hi,
We are using the BLE keyboard example as a basis for a design and notice strange behavior.
Only change was to create a custom_board.h header for a button press on...
Hi,
I can use the DFU bootloader via HCI/UART to update the application image.
Reference DFU init pakcet . The init packet contains a 4-byte value identifying the version...
I searched the database but did not find an answer to my question.
My environment is as follows:
Keil uVision v5.18a
Nordic SDK 11
nRF52 PCA10040
Softdevice S132
...
Hello,
I am trying to write data to flash. I did successful write data to flash, but I need delays between erases and writes. I tried to avoid the delays with the NRF_EVT_FLASH_OPERATION_SUCCESS...
Hello,
I am currently using Renesas RL78 BLE chip and the UAP & NAP address is as follows 42-00-DE.
Now, for better performance, I migrated to Nordic nRF51422 and am...
Hi all,
I have to transfer a lot of data over the UART channel, and run into some problems...
First problem was/is the UART FIFO Size.
There are three different defines...
