I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
We use Rigado BMD-300 module with nRF52832 and softdevice S132 v6.1.0 as peripheral. Trying to create test plan for Bluetooth qualification , but with new TCLR there are inconsistencies...
Hi,
Recently, I faced very weird problem which stops working MCU when MCU enters low-power mode.
Not all PCBA I made have the same problem but quite many PCBA shows the...
hello, this is my first time to start the PPK, I have a 52840 DK (BMD-340-EVAL) and PPK, when I use nRF connect to connect the PPK(PPK is over the 52840 DK) , it shows Failed...
Hi Nordic Community
I'm busy developing a board around the nRF9160. Do you have a KiCad library/component for the SOC, do I need to make one myself, and if you do have one...
I'm trying to use the SPIM driver on nRF52832. The setup is:
Chip: nRF52832
SDK: 15
Softdevice: s132 v6
Toolchain: GCC
For some reason the call to nrfx_spim_xfer...
Hello,
I'm trying to configure the max -min of interval params and supervision timeout to obtain timeout of android = 1s.
i configure all parameters to run function...
Hi,
I am using the nrf-52840 DK.
I modified the pwm_library to output 125khz frequency.
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(125000L, NRF_GPIO_PIN_MAP...
Hi ,
The nrf connect for desktop programming works good on my desktop before.
The tool shows error message "cannot find module 'usb' " today.
I ever try re-install the...
I am working on integrated peripheral and central device used for indoor positioning. The device has two modes, at boot it is a peripheral for some duration of time then it...
Hello, we have been using a nRF51822 8-pin RF module for a while now for various products, the pinout is as follows: power, P0.00, P0.01, P0.09, P0.11, SWDIO, SWDCLK, ground...
Hi I try to implement DFU to our application using Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0 When I use the DFU-Example everything works fine. I then implemented the DFU-code from...
Hi there, I have a custom board with nRF52840 and i am transferring fairly large amounts of data via uarte. I am also using my own driver. For some reason the attached device...
Hi,
I am Using NRF52840-DK Board. We are trying to transmit multiple data using NRFx_SPIM Example. for single reg read it is working fine.
please check below code is...
Hi,
I have certain doubts regarding simple message model .
1. Why simple_message_client_init or simple_message_server_init is never used? Don't we need this function to...
