Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi, I am using nordic nrf52832 module with BLE mesh SDK V2.2.0 I want to do DFU for application + softdevice without any serial connection through mobile app between BLE mesh...
I got the fail result of the test CPS/SEN/SPE/BI-05-C [Cycling Power Control Point Procedure Timeout].
At this test, the tester does not send the confirmation until ATT...
Hi Team Nordic,
According to the AM2302 (DHT22) datasheet, the data pin will be pulled to high state in idle state. But in my case, when i am reading the data pin before...
I'm developing nFR52832 to communicate with the PC via UART. commands are sent to the nRF and for each command nRF responds with some data back to the PC via UART.
The UART...
I'm trying to include the SPI driver in my project.
I have added the .c file into my project:
I have included the path into the project:
I have enabled the SPI...
I try to make bootloader via USART for my application. I'm using: nRF51422rev.2, SDK6.1.0, S210 ver3.0.0. KEIL5.11. I did everything like describes in post here:
devzone...
I want to implement BLE security in one of my project where central and peripheral connection should be secured rather than only characteristic protection.
And any way to...
I'm developing a custom driver (C++) for the SPI master. Somewhere I've made a mistake, where the first received byte is written with a memory offset in SPI mode 1. I.e. we...
Hi,
I have a BLE application, which I want to interface with PC via serial communication through USB.
It seems that just adding Softdevice breaks the USB_CDC_ACM example...
Hi all,
As a followup of this question, I started with the Thingy Mesh Provisioning Demo v0.5. However, I cannot get this version working possibly due to some unclear points...
Hi,
Am developing a beacon using nrf52810. I have a doubt on how to program the nrf52810 which I made using the schematics and layouts given in the Nordic website for nrf52810...
I am noticing that FDS requires me to specify a "record size", but there is no maximum specified, so I am testing it. Currently my program attempts to store 32 words, but...
I want to add some code to static void app_onoff_server_set_cb(const app_onoff_server_t * p_server, bool onoff) in light switch server application.
My intention is when...
