Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
I tried to send data through the proprietary radio. My devices are NRF52832. The data I would like to send is an uint8_t array:
Right before I send it out, I...
Hi everyone,
My English skill is not good, but I really want to share this problem to all developers that I spent three hours for it.
Example nRF5_SDK_for_Thread_and_Zigbee_2...
Hi!
I have questions for Nordic developers team. What capacity of network is possible with nrf52840 thread mesh? I've tried to attach large amount of nodes to mesh and...
Hi Guys,
I want to use the TWI for my mesh application in which I want to read out 2 sensors (Sensirion SHTW2 and SGCP3) and then send the sensor values over a mesh network...
Hi all,
I´m using nrf52832 with sdk 14.2.0 and softdevice s332.
I have opened and closed the eclipse. Now when I open it, it compiled and gives me this error that I did...
Hi,
I am using nRF_SDK_15.0.0?a53641 and writing a program with keil.
I am trying to read data from the acceleration sensor( LSM303DLHC ) by communication with BLENanov2...
Hello
I just started learning nrf52832 DK and run few of the examples. I wanted to start developing my own application based on the examples. Right now, I want to read...
Hello, I have some confusion about updating advertising packet dynamically.
I am using nrf52832 with SDK v12.3.0. I am sending datas from sensor in advertising packet(manuf...
Hi,
I am trying to build the ble_connectivity code "ble_connectivity/pca10040/ser_s132_uart" to test the serialization part. The scan is not working. I am using PCA10040...
18.9.13 RAM[0].POWERSET (and sections associated for other RAM sections) states:
When read, this register will return the value of the POWER register.
however the...
Dear Sir,
I was using my Rigado BMD 300 and it was working fine.
When I open the nRFGo Studio the following was the details displayed in the tool.
But sometime after...
Hi there,
I am struct for two days trying to send 6 packets of 20 bytes as central. I use ble app uart central sample from nrf5_sdk11.0 with nrf51 S130 v2.0 softdevice...
Hi,
Does anyone know how to receive voice data from Nordic 52832 remote control in embeded linux ? Does Nordic provide any package for this purpose ?
Thanks
Hi, everyone,
We are developing the project on nRF52832 chip that is built from master (multirole) and slaves modules. The master program (in our case master is multirole...
I want to send data to all node by mesh 2.1.1.
From the Mesh profile(3.4.2.4 Group address),the dst_addr = 0xFFFF is send to all node .
I try to setting "packet_tx()"funtion...
