Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I'm using NRF52832 and a core adaptation for Arduino IDE. In my project I'm using both TWI and SPI interfaces. If for TWI I manage to reduce the current during sleep...
Hi everyone,
I am using a chip nRF52832 reading data from LIS2DH12 via TWI (all in a custome boad), then data will be send to Master nRF52832 DK ia BLE_NUS. However, when...
I have a new nRF52840 Dongle which seems to have either had a hardware failure while updating its bootloader or the updating was unsuccessful and now the device does not flash...
To do some test, I need micros(). This is the reason why I couldn't use RTC or app_timer.
When I tried timer example(nRF5_SDK_12.2.0_f012efa\examples\peripheral\), I could...
Hello, I need to use PWM to control GPIO and integrate it to work on simple COAP server app using nrf52840 DK.
I used "pwm_simple" example from SDK (not Thread/Zigbie SDK...
Hello.
When I try to initialize provisioning bearer gatt with turned on the proxy, provisioning bearer is reconfigure the mesh_gatt which it will not work with proxy anymore...
Hello,
I started developing a Thread-Solution with my NRF52840-DK. Now I'm searching if there is a Message Sequence Chart (like for the BLE solution) also for the Thread...
Hi,
I'm testing the below example code, found on devzone, on mesh sdk 2.2.0.
I'm experiencing a strange issue on the read side. On the first read after the write I always...
Hi,
I have an application (central mode) which regularly connects to a number of clients, read characteristics and then disconnects again.
Whenever there is an unintended...
I'm have nRF52 DK, wish use nrfutil (v4.0.0) to update target firmware. Works fine when using -n "Target Name", but I get a "Device not found" when trying to use parameter...
I have a custom designed PCB that has the nRF52832 (taiyo yuden EYSHCNZWZ) on board.
When I flash the board using pogo pins and the jlink (debug out) from a nRF52DK, everything...
Hi,
I am using the nRF51 dongle to connect and subscribe to specific characteristic and i am getting notification correctly but when subscribing to another notification...
Hello,
are there any plans / work in progress to support 802.15.4 radio in mbedOS?
Currently nRF52840-DK is a supported target platform but if you want to work with
...
Hi all,
I am using power profiler kit to measure as mentioned below screenshot.
I want to achieve current number as mentioned in Nordic product specification as" IOFF_RAMOFF_RESET...
Hi,
I'm using nRF52832 with IAR and SDK V15, S132.
I incorporated the peer manager in the uart serial profile example.
I assume, since I have 3 pages (inc. GC) set in...
