void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I have a project about Bluetooth enable lock. I am going to use to BT832 module. Do i need recertifation for Bluetooth brand?. I dont know what to do. Do i need being member...
Hi!
We are developing an IoT device using the nRF52832. 2 years ago in this thread, https://devzone.nordicsemi.com/f/nordic-q-a/27099/nrf52832-ble-certification-under...
I'm combing over the CLI peripheral example, but having a few problems when running the example:
The Debug Terminal in SES blacks out the test so its difficult to see...
Hi I have developed and Android application to connect for 2 BLE Devices one after other.
These 2 BLE devices connection and service discovery will happen one after the...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask if central can make connection request without scanning (central know the mac address...
Hi everyone,
I have migrated my project from SDK for Mesh v2.1.1 to v3.0.0.
I am getting a Mesh Assert when the Mesh is trying to request a radio timeslot after the "NRF_EVT_RADIO_BLOCKED...
Is it possible to run Eddystone example from SDK12.3.0 on nRF51822 xx aa chip?
In the eddystone documentation it mentioned that S132 softdevice required, but on older SDK...
Dear Nordic,
Hi,i'm looking for an easy way to make Wlan coexistence with Ble,i know there has a solution that named 3rd party, just like this:
So, What i want to...
when we pass the BLE event handler as a function argument to BLE stack init function and register the function results in a deadlock mechanism. Is that we cant able to register...
Hi Guys,
I have a general question to the mesh functionalities. We built a mesh sensor network and I now want to now if it is possible to decrease the data-rate to increase...
Hi,
I just completed the migration from mesh sdk 2.2.0 to 3.0.0.
After running the project it get stuck at line 422 of timeslot.c in function timeslot_sd_event_handler...
Hi all,
So I've developed a custom board with the NRF52832 qfaa e1 and using Mbed OS 5. System on current is around 3.5uA when not using BLE.
When using BLE my idle current...
I'm learning NRF51822.Now,I want to develop it with PC.I need connected Nrf51822 & PC with Ble.What tools can I use? .I designed a Nrf51822 pcb based on CH340.
