Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
HI all,
I'm trying to get the Thingy Mesh Demo v0.1 working on my Thingy's. I am using the same SDK version as used in the demo ( Nordic nRF5 SDK for Mesh v1.0.1) and I...
I was able to follow the "quick start" guide for Mesh DFU and got things working with 3 nodes.
1 node (the serial host hooked to the PC) was programmed with:
bin/softdevice...
Hi to all,
i am developing a device with nrf51822 soc. i am using nrf51822 custom board, my board is https://pl.aliexpress.com/item/2V-3-3V-NRF51822-Bluetooth-4-0-Wireless...
Hi, everyone.
I am currently doing research for our new project - IoT alarm system for smart home.
One of requirements is Wi-Fi / BLE combo chip / module . Multi-protocol...
Hi all,
in Central mode I would like to retrieve the list of all the devices present.
I have developped a litle USB dongle, and I need to list alls peripherals, but after...
Hello,
I am using hardware PWM on NRF52832 in order to drive a MOS. I found something unexpected with the rates. i understand the PWM rate is determined by the clock divider...
So I'm trying to merge the ble_app_uart example with a project of my own, using SDK 14.2.0, but keep getting errors with the ram.
At first, my own project's ram start was...
NRF_LOG_ERROR should be coded not NRF_LOG_DEBUG for error conditions.
Not only will the log calls not be compiled and not displayed if
NRF_LOG_DEFAULT_LEVEL is less than...
Dear Madam/Sir,
I'm measuring the nRF52840 DK current consumption with my custom ble_peripheral app and other example ble_peripheral apps, namely ble_app_proximity, ble_app_pwr_profiling...
Hello,
I'm using the nRF51422 uController and the SDK 11. I tranferd from Keil to Eclipse and followed the tutorial to do so. But now I got a Problem while flashing my...
Hello Nordic team
I am working on "ble_app_uart_pca10056_s140" SDK V-15.2. IDE: Segger Embedded Studio.
After compiling above project I am trying to download two files...
nrf52840
sdk 15.2
i am using termite for serial viewer. and problem is my code gets complied with no errors and when i open termite there is no data in termite. i checked...
As it is stated in documentation, RTS is active low. But a peripheral device we use expects it to be active high. Can this be changed in software somehow or it requires a...
Using NRF5 SDK 15.0.0 with nrf52832.
I'm curious about the intended use for the BUTTON_HIGH_ACCURACY_ENABLED flag in the button module. I have a project where the main loop...
