But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
In my project I have to implement passkey or whitelist in the conection with...
Hi,
I'm trying to run the OTA DFU for the nrf52832 (sdk v14.2, softdevice v5.1) from multiple devices.
In the OTA script, I enabl the receipt notifications and it works...
I am working out of this MPU-twi example and am trying to validate sent data by printing it to the serial monitor. From what I've seen in SDK 15.1.0 examples, it seems like...
Hi,
I am using nRF5 11.0.0 SDK softdevice 2.0.0.
I have implemented a RTOS application with beacon adv.
I also want to add UART service to the RTOS application.
...
Hi,
I am trying to use the Power Profiler Kit (PPK) to asses the power consumption on a nRF52840 - PDK. I have not managed to get anything wokring.
The exact hardware...
I am using 3 nRF 52840 dongles and want to establish mesh network between them. So I flashed the dongle with the softdevice (s140_nrf52_6.0.0_softdevice), bootloader (mesh_bootloader_serial_gccarmemb_nrf52840_xxAA...
I have flashed the the mesh serial hex file to nRF52840 dongle through nRF connect programmer application. I am getting following error
1. Reopen device failed
2. Nordic...
Hello All, In one of our product we are using nrf52840 Bluetooth + MCU IC. Size of Product is very tiny. which types of Antenna is better for range of 25 meter to 30 meter...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
Hi, I wrote the firmware in SDK 11 preview, and when migrating it to SDK 11 the NFC code does not work, also it seems when the NFC startup code is executed none of the GPIO...
Hi All,
I've not enough experience in nrf51822. I'm developing a battery powered device using the Nordic nrf51822 pca10028. I want to connect two nrf51822 pca10028 boards...
I would like to use the latest ARM Compiler Version 6 ( armclang ) because I need some features of the C++11 language.
Is it possible to use the latest ARM Compiler Version...
Hi all,
I am using keil uVision 5 and nRFgo studio version 1.21.
I am trying to flash softdevice and application in nRF52832, but my device(nrf52-DK) is not getting connected...
